Trane Foundation GBC Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 31 / 40

RT-SVX069A-EN 31
W WA AR RN NIIN NG G
R Ro otta attiin ng g C Co om mp po on ne en nttss!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err b be effo orre e sse errv viicciin ng g
cco ou ulld d rre essu ulltt iin n rro otta attiin ng g cco om mp po on ne en nttss ccu uttttiin ng g
a an nd d sslla assh hiin ng g tte ecch hn niicciia an n w wh hiicch h cco ou ulld d rre essu ulltt iin n
d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Du urriin ng g iin nsstta alllla attiio on n,, tte essttiin ng g,, sse errv viicciin ng g a an nd d
ttrro ou ub blle essh ho oo ottiin ng g o off tth hiiss p prro od du ucctt iitt m ma ay y b be e
n ne ecce essssa arry y tto o w wo orrkk w wiitth h lliiv ve e a an nd d e ex xp po osse ed d
rro otta attiin ng g cco om mp po on ne en nttss.. H Ha av ve e a a q qu ua alliiffiie ed d o orr
lliicce en nsse ed d sse errv viicce e iin nd diiv viid du ua all w wh ho o h ha ass b be ee en n
p prro op pe errlly y ttrra aiin ne ed d iin n h ha an nd dlliin ng g e ex xp po osse ed d rro otta attiin ng g
cco om mp po on ne en nttss,, p pe errffo orrm m tth he esse e tta asskkss..
N NO OT TIIC CE E
E Eq qu uiip pm me en ntt D Da am ma ag ge e!!
F Fo orrcciib blly y ttu urrn niin ng g tth he e m mo otto orr ssh ha afftt cca an n d da am ma ag ge e
tth he e g ge ea arr ttrra aiin n a an nd d m mo otto orr b be ey yo on nd d rre ep pa aiirr..
N Ne ev ve err ttu urrn n tth he e m mo otto orr ssh ha afftt b by y h ha an nd d o orr w wiitth h a a
w wrre en ncch h..
☐ Verify that all damper linkages move freely;
lubricate with white grease, if necessary.
☐ Check supply fan motor bearings; repair or replace
the motor as necessary.
☐ Check the fan shaft bearings for wear. Replace the
bearings as necessary.
☐ Check the supply fan belt(s). If the belts are frayed
or worn, replace them. Refer to the
“Fan Belt
Adjustment-Belt Drive Units,” p. 29 for belt
replacement and adjustments.
☐ Verify that all wire terminal connections are tight.
☐ Remove any corrosion present on the exterior
surfaces of the unit and repaint these areas.
☐ Generally inspect the unit for unusual conditions (e.
g., loose access panels, leaking piping connections,
etc.)
☐ Make sure that all retaining screws are reinstalled in
the unit access panels once these checks are
complete.
☐ With the unit running, check and record the
following:
– ambient temperature
–
compressor oil level (each circuit)
– compressor suction and discharge pressures
(each circuit)
– superheat and subcooling (each circuit)
Record this data on an “operator’s maintenance log”
like the one shown in Sample maintenance log table in
Final Process Section. If the operating pressures
indicate a refrigerant shortage, measure the system
superheat and system subcooling. For guidelines, refer
to
“Compressor Start-Up,” p. 27 .
IIm mp po orrtta an ntt:: Do not release refrigerant to the
atmosphere! If adding or removing
refrigerant is required, the service
technician must comply with all federal,
state and local laws. Refer to general
service bulletin MSCU-SB-1 (latest edition).
Heating Season
☐ Inspect the unit’s air filters. If necessary, clean or
replace them.
☐ Check supply fan motor bearings; repair or replace
the motor as necessary.
☐ Inspect both the main unit control panel and heat
section control box for loose electrical components
and terminal connections, as well as damaged wire
insulation. Make any necessary repairs.
☐ Verify that the electric heat system operates
properly.
Coil Cleaning
Regular coil maintenance, including annual cleaning
enhances the unit’s operating efficiency by minimizing
the following:
• Compressor head pressure and amperage draw
• Evaporator water carryover
• Fan brake horsepower
• Static pressure losses
• Airflow reduction
At least once each year, or more often if the unit is
located in a “dirty” environment, clean the condenser
coils using the instructions outlined below. Be sure to
follow these instructions as closely as possible to avoid
damaging the coils.
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss C Ch he em miicca allss!!
C Co oiill cclle ea an niin ng g a ag ge en nttss cca an n b be e e eiitth he err a acciid diicc o orr h hiig gh hlly y
a allkka alliin ne e a an nd d cca an n b bu urrn n sse ev ve erre elly y iiff cco on ntta acctt w wiitth h sskkiin n
o orr e ey ye ess o occccu urrss..
H Ha an nd dlle e cch he em miicca all cca arre effu ulllly y a an nd d a av vo oiid d cco on ntta acctt w wiitth h
sskkiin n.. A AL LW WA AY YS S w we ea arr P Pe errsso on na all P Prro otte eccttiiv ve e
E Eq qu uiip pm me en ntt ((P PP PE E)) iin nccllu ud diin ng g g go og gg glle ess o orr ffa acce e ssh hiie elld d,,
cch he em miicca all rre essiisstta an ntt g gllo ov ve ess,, b bo oo ottss,, a ap prro on n o orr ssu uiitt a ass
rre eq qu uiirre ed d.. F Fo orr p pe errsso on na all ssa affe etty y rre effe err tto o tth he e cclle ea an niin ng g
a ag ge en ntt m ma an nu uffa accttu urre err’’ss M Ma atte erriia allss S Sa affe etty y D Da atta a S Sh he ee ett
a an nd d ffo ollllo ow w a allll rre ecco om mm me en nd de ed d ssa affe e h ha an nd dlliin ng g
p prra accttiicce ess..
M Ma aiin ntte en na an ncce e