Trane *DH2B060A9V3VA Скачать руководство пользователя

Страница: 35 / 44

Service Facts

X343070P08

YES

Is pressure greater

than pressure

switch label?

See Note #2

Replace pressure switch.

Check operation.

Is the inducer

motor running?

Is 24 volts present,

measured across PS1

(orange to yellow/6)?

See Note #1

Disconnect electrical

power from the furnace

and remove 1 wire from

each pressure switch

Is continuity

measured across

PS1 or PS2?

Replace pressure switch.

Check operation.

YES

Note #1

24 volts = Open Switch
0 volts = Closed Switch

DEFINITION
An error has occurred with the PS1 or PS2.

The error will be reported, indicating that the pressure switch
is either opened or closed, contrary to normal operating
sequence.

In most cases, the pressure switch is not the problem.

Note: Verify all wiring to pressure switch is
correct per wiring diagram

Note #2

Measured pressure is
negative, greater than refers
to magnitude only.

3 Flash Fault LED

Replace Inducer.
Check operation.

YES

While the furnace is operating on 1

stage heat make a call for 2

stage

heat. Allow (30 seconds) for the

furnace to transition to 2

stage.

Is 24 volts present,

measured across PS2

(yellow/7 to brown)?

See Note #1

Is pressure greater

than pressure

switch label?

See Note #2

Replace pressure switch.

Check operation.

Cycle power to the furnace

and call for 1

stage heat.

YES

Replace or repair wiring

harness. Check operation.

YES

Reconnect electrical

power to furnace. Cycle

power to furnace and call

for 1

stage heat.

Does the

furnace run on

stage?

YES

Check PS hose, flue piping for

obstruction and/or confirm vent

size is correct

Check PS hose, flue piping

for obstruction and/or

confirm vent size is correct

Pressure

switch is okay.

Pressure switches

are okay. Re attach

each wire to PS

Is voltage measured at

IFC plug between pins

1 (BK/6) – 2 (RD/6)

2 (RD/6) – 3 (WH/6)

1 (BK/6) – 3 (WH/6)?

YES

See IFC Component Layout for

location of plug.

Is voltage measured at

inducer motor plug

between pins

1 (BK) – 2 (RD)

2 (RD) – 3 (WH)

1 (BK) – 3 (WH)?

Replace IFC.

Check operation.

Pressure

switch is okay.

Содержание *DH2B060A9V3VA













































Результаты поиска

Содержание *DH2B060A9V3VA

Отзывы:

Похожие инструкции для *DH2B060A9V3VA

Бренды по названию

Популярные бренды

Trane *DH2B060A9V3VA, Сервисные данные

Результаты поиска

Содержание *DH2B060A9V3VA

Отзывы:

Похожие инструкции для *DH2B060A9V3VA

Бренды по названию

Популярные бренды