manualshive.com logo in svg

Trane BAYCOIL55, Руководство по установке

Поделиться
Скачать
Trane BAYCOIL55 Скачать руководство пользователя страница 2

2 

 

18-AH47D1-2

Section 1. Safety

▲

WARNING

!

This information is intended for use by individuals 
possessing adequate backgrounds of electrical and 
mechanical experience. Any attempt to repair a central 
air conditioning product may result in personal injury 
and/or property damage. The manufacture or seller 
cannot be responsible for the interpretation of this 
information, nor can it assume any liability in connec-
tion with its use.

Extreme caution should be exercised when opening 
the Liquid Line Service Valve. Turn counterclockwise 
until the valve stem just touches the rolled edge. No 
torque is required.

LIVE ELECTRICAL COMPONENTS!
During installation, testing, servicing, and trouble-
shooting of this product, it may be necessary to work 
with live electrical components. Failure to follow all 
electrical safety precautions when exposed to live 
electrical components could result in death or serious 
injury.

▲

CAUTION

!

▲

WARNING

!

CONTAINS REFRIGERANT!

SYSTEM CONTAINS OIL AND REFRIGERANT UNDER 

HIGH PRESSURE. RECOVER REFRIGERANT TO RELIEVE 

PRESSURE BEFORE OPENING SYSTEM.
Failure to follow proper procedures can result in personal

illness or injury or severe equipment damage.

CAUTION

!

▲

CAUTION

!

SAFETY HAZARD
Sharp Edge Hazard. Be careful of sharp edges on equip-
ment or any cuts made on sheet metal while installing or 
servicing. Personal injury may result. 

Содержание BAYCOIL55













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды