pbCTflk clroW lmboATfkd Tfmp
NF qhe qemperature aial can be changed at any time to increase or decrease the
cooking temperature of the drillK qhe efdeLefdebo qemperature settings are for
drillingK qhe jbaLjfa oAkdb qemperature settings are for plow `ookingK qhe
pjlhb setting is for pmoking and adding pmoke clavor to foods being cookedK qhe
pjlhb setting can also be used to “hold” foods at approximately NUM to OMM degrees
cK
OF vour qoAbdbo mbiibq dofii should never be moved while it is hotK ff you are
transporting your drill in a vehicle after cooking on itI make sure the fire is completely
out and the drill is `lia before placing it in any vehicleK kbsbo put water into the
cirepotK ft will jam the AugerK
PF qhe qoAbdbo mbiibq dofii is designed to operate with the aoor `ilpbaK
`ooking with the aoor open greatly lengthens your cooking timeK
QF kbsbo add mellets by hand to a hot cirepotK qhis is dangerous and you may be
seriously burnedK ff you run out of mellets and lose your fire while cookingI let the drill
completely cool and start again with the
fkfTfAi cfofkd fkpTorCTflkpK
RF jake sure the eeat Baffle is properly seated on its locating bracketsK qhe long lips of
the eeat Baffle should be pointing down over the cirepotK ff not seated properlyI direct
heat and flame could come up out of the cirepot and cause a grease fire in the drillK
SF then estimating cooking timesI the outside temperature will be an important factorK ff
it is hot outsideI it will take less time for food to cookK ff it is coldI wet or windyI it will
take longerK
TF drease fires are caused by not properly maintaining the drill by failing to clean your
drease arain manI sJshaped drease arain and drease arain qube on a consistent
basisK fn the unlikely event of a grease fire while cookingI
Trok Teb ptfTCeLafAi
to perT altk CvCib and hbbm Teb allo Cilpba
until the fire is completely
outK kever keep the aoor open during a grease fireK ff it does not go outI lightly
sprinkle baking soda on the fireK
Be careful not to burn yourselfK
ff this does not
workI then carefully remove the food from the drill and keep the aoor closed until the
fire is completely outK
AgainI be careful not to burn yourselfK
then the drill is
completely coolI remove the morcelain drill and replace the foil on the drease arain
manK `lean any grease accumulation from the sJshaped drease arain and the
drease arain qubeK oeplace the drease arain man and the morcelain drill in their
proper positionsI restart the drill and resume cookingK
pbCTflk cfsbW MAfkTAfkfkd
vlro kbt dofii
NF `hange the aluminum foil on the drease arain man frequentlyK meriodicallyI clean the
grease out of the sJshaped drease arain and drease arain qube and off of the
interior surfaces of the drillK bmpty the drease Bucket occasionally and line with
aluminum foil for easy cleanJupK ft is easier to clean off accumulated grease when the
drill is warmK
Bb CAobcri klT Tl Brok vlropbicK
ff too much grease is
allowed to build up on the drease arain man and in the sJshaped drease arainI or is
allowed to plug the drease arain qubeI a grease fire could resultK te recommend
cleaning these locations regularlyK
OF lutside surfacesW al klq use oven cleanerI abrasive cleansers or abrasive cleaning
pads on the outside drill surfacesK rse warm soapy water to cut the greaseK
