background image

Assembly Overview

Step 1: Check all parts against the component list

Step 2: Assemble the rear wall panels 

Step 3: Assemble the side wall panels

Step 4: Assemble the front wall panels

Step 6: Assemble the ridge beam

Step 7:

Step 8:

Handy Tips Before You Begin

How to drill rivet holes in panels – Use a 4.2mm drill bit, set your drill clutch to the drill bit icon. Make a 

mark where you want to drill and use this to start the hole.

Drilling tek-screws – Drilling tek screws into the panels can sometimes cause the corrugation to buckle 

in, making it tricky to get the screw all the way in. An easy fix for this is to place a small block of wood 

underneath the corrugation as you drill, providing support for the panel until the screw is all the way in. 

Make sure the block is not directly underneath the screw. 

How to remove rivets if needed – Don’t worry if you have placed a rivet incorrectly or you need to 

adjust a panel, they are easy to remove. Just drill directly through the top of the rivet using the same drill 

bit you used to make the hole. This will remove the rivet head, causing the whole rivet to fall out.

OTHER TIPS

 

●  Very Important – make sure you remove metal drill filings to prevent corrosion and scratches. 

     Removing metal filing and avoiding scratching the shed during assembly will help prevent any 

 corrosion later on.

 

● Peel off part number stickers and clean 

 soap/water.

 

●  Use silicone to further weatherproof seals around the shed (not included).

iii

with

Step 5: Constructing the walls and gables

 Assemble the roof 

Assembling the Support square tube

Step 10: Assemble the door

 

Step 9: Fitting  Wall Bracing

Содержание GS512-V1























Отзывы: