TracVision R4SL Скачать руководство пользователя страница 1

Страница: 1 / 6

TracVision R5SL/R4SL

RF PCB Replacement Instructions

TracVision

R5SL/R4SL RF PCB Replacement

Instructions

The following instructions explain how to replace the RF PCB (printed
circuit board) in a TracVision R5SL/R4SL.

Tools Required

TIP:

The Flash Update Wizard is now available to KVH-authorized

dealers through the KVH Partner Portal at

www.kvh.com/partners

• #1 Phillips screwdriver

• #2 Phillips screwdriver

• 7/16" open-end wrench

• Needle-nose pliers

• PC with the latest version of the Flash Update Wizard

installed

Be sure to avoid causing sharp bends in cables when securing or
rerouting cables in the following procedures. Sharp bends or
kinks in cables can degrade antenna performance.

IMPORTANT!

CAUTION

For your own safety, be sure to disconnect power from all wired
components before performing this procedure.

54-0440 Rev. A

Содержание R4SL







Результаты поиска

Содержание R4SL

Отзывы:

Похожие инструкции для R4SL

Бренды по названию

Популярные бренды

TracVision R4SL, Инструкция по эксплуатации

Результаты поиска

Содержание R4SL

Отзывы:

Похожие инструкции для R4SL

Бренды по названию

Популярные бренды