background image

11.08 MODEL

3

Press the + / - keys to select PT items, choose good press ENT key, the black 

box flashes by + / - keys to adjust the value. After this adjustment, press the ENT 

key to confirm. When the black box is not flashing, then through the + / - keys to 

select an item to adjust. Range: 0% - 100% (the default value is 0%) 

Step with PT entry, select and set WD items. Range: 0% - 100% (the default is 0%) 

Step with PT entry, select and set CY items. Range: 0 - 30 (default is 0) 

Step with PT entry, select and set DT items. Range: 0 - 5 (default is 0) 

Press EXIT to save and return to FUNCTION interface, 

Notes abbreviated terms: 

PT - Position of the throttle trigger when ABS works. 

WD - Brake return amount. 

CY - Cycle speed. ABS operation cycle. The smaller the value, the faster the cycle. 

DT - From the braking point back to the time of the release point.

This function is used to select the model 

memory, supports six sets of memory. 

1. Press ENTER to enter the FUNCTION 

interface, 

2. Use the + / - keys to select the module 

memory function, press ENTER 

3. Use the + / - keys to select the move 

instruction arrows. 

4. Press ENTER to save the selection. 

5. Press EXIT to save and return to 

    FUNCTION screen, 

Note:

 When change modes, servos delay may happen, you can solve this 

problem by re-switch on transmitter.

11.09  FAIL SAVE

11.10  MULTI OPT

If the signal loss occurs, the receiver can 

set the value of throttle servo to the fixed .

1. Press “ENT” to enter the FUNCTION 

interface   

2

Use the + / - keys to select the FAIL SAFE 

function, press ENT key to enter, and press-

ing ENT key to select ON / OFF. Use the + / - 

keys to select “ SET “

3

Put the throttle trigger to set TH f/s value 

and press ENT saved ” Successful” appears 

This function is used to turn on or switch 

off remote control buzzer. Turning on the 

TH HOLD and achieve the 2CH and 3CH 

special mix function.

 

1. Press “ENT” to enter the FUNCTION 

    interface. 

2. Use the + / - keys to select the function, 

    press ENT key to enter 

3. Press EXIT to save and return to 

    FUNCTION screen

on the screen, F/S setting successfully.   

4

Press EXIT to save and return to FUNCTION screen, 

TH – throttle values   : 1000US ----- 2000US,  1500US is default neutral position.

SET DATA: To be setted F/S valuve.

NOTES

: For your safety, when has setted F/S function. Before playing, checking 

F/S function work is very necessary

NOTES

: The TH HOLD adjust value is 0 – 100 . setting 100 corresponding the value 

of 40% of the maximum throttle value. Before the setted throttle value put the trigger, 

the throttle slow acceleration till to setted throttle value. The setted throttle value is 

minimum throttle. As long as no brake, put the trigger in neutral position, the throttle 

keep the setted throttle. When setted the TH HOLD, brake or switch on the Tx need 

put the trigger to start the setted throttle.  2, The 2CH and 3CH mix control. The 3CH 

servo just unilateral movement. This special function used for cars or motorbikes 

with brake disk system. The reverse to be justed in function 11 .03 reverse function.

13

12

Содержание TS3T












Отзывы: