Rope breakage.
1.
Never allow anyone to be positioned between anchor and winch. If rope breaks it could snap back and cause injury.
2.
If the included anchor roller is ever replaced it must be replaced by a closed loop anchor roller to prevent the anchor line from
snapping onto the boat deck in the event the rope breaks.
3.
Always use an anchor rope with minimum 700 pound tensile strength for this product. Never substitute cable for rope.
4.
This product is intended to lift short shanked river & mushroom anchors. Do not attempt to lift objects overhead.
5.
Inspect entire rope for weak or worn condition. Replace worn rope with anchor rope with a min. 700 lb break strength.
Electrical shock and fire hazards.
1.
Do not use electrical wire sizes smaller than 12 AWG (gauge) with a 105-C temperature rating. Using wire that is too small could
result in overloading and a fire. Larger gauge wire is permitted.
2.
Use the supplied 20 amp circuit breaker or a 30 amp in-line fuse when installing this winch.
3.
Always disconnect the battery lead wires from the battery before attempting to install, relocate, or service the winch.
Cruising and boat trailering hazards
–
As a precaution, when the boat is cruising the anchor must be secured
with the safety cable provided. When the boat is being trailered, the anchor must be placed inside the boat or tow vehicle. If the anchor
breaks free during cruising or trailering, it could cause serious damage and/or injury.
Entanglement hazards.
1.
Never place any object or tool in the rope spool while retrieving or deploying the anchor. The tool or object could become tangled in
the rope resulting in serious injury and/or damage to the winch.
2.
Do not wear loose fitting clothing, scarves, or neck ties during the operation of the winch. Loose clothing may become caught in
moving parts resulting in injury or death.
3.
Do not operate the winch under the influence of drugs and/or alcohol.
Storage and Maintenance
–
For storage, it is best to disconnect positive wire from battery.
CONNECTING THE WINCH TO BATTERY POWER -
Do not use wire sizes smaller than 12 AWG with 105-
degree C rated insulation. Using wire that is insufficient could result in overloading and a fire. The use of larger diameter wire is encouraged
and can improve the flow of electrical current. If longer wire is required, use the next larger wire size (10 AWG) for your installation. Use the
supplied circuit breaker or an in-line 20-amp fuse. Using incorrect circuit breakers may result in fire. Always disconnect battery wires
from the battery before attempting to install, relocate, or service the winch.
ROPE INSTALLATION
–
Nylon anchor rope is pre-installed, but when you need to install new rope,
insert the rope through the hole located on the inside of the spool/drum and tie an overhand knot on the outside of the spool so the
knot can be pulled into the countersunk hole on the outside end of the spool. Pull the rope so the knot is tight against the counter
sunk hole. Make sure the rope is not tangled and not looped around anything and is free to wrap on the spool. Hold tension of the
rope while wearing a glove. Press the “UP” direction o
n the switch and hold until the rope is neatly wrapped on the spool. Release
the switch button at anytime during the wrapping of the rope on the spool if an unsatisfactory wrap is occurring. The spool will hold
100’ of 3/16” (5mm) anchor rope
or 90 feet of
¼”
(6mm) rope. Use nylon anchor rope with minimum of 700 pounds of tensile
strength.
WIRELESS REMOTE IS PRE-PROGRAMMED AT THE FACTORY
It consists of a compact, sealed hand-held controller (sending unit) that
allows push-button anchor operation from any location within about 50 feet, and a receiving unit that is already installed in the winch. Also
included is a remote bracket to store the remote and to allow the remote to act as a panel switch if placed near the helm, or removed for
portable use anywhere near the boat. The remote is pre-programmed at the factory for your specific winch. One remote cannot operate two
winches. Every remote has a unique code so there is no concern about having two remotes control one winch.
If re-programming the remote becomes necessary, follow the instructions below:
1.
Disconnect battery power.
2.
Press
and hold
any button on remote (do not release button until step 3).
3.
Re-connect battery power, continue to hold remote button for 2 seconds, then release.
4.
Test winch operation. Reprogram is necessary.
