background image

 

 

OPERATING PROCEDURE 

 

BEFORE STARTING:

 Follow engine manufacturer’s instructions in preparing engine for 

operation

.  Never fill fuel tank indoors, with engine running or while engine is hot.  Do not smoke while 

filling tank. 

1.  Inspect area to be vacuumed and pickup all harmful objects and litter.  Rocks and other    
      harmful debris can do serious damage to vacuum assembly and cause bodily injury.

 

2.  For best vacuuming results, operate tractor at manufacturer’s recommended speed for best   
     cutting.  If grass is high, mow first and vacuum on the second pass. 
3.  Your vacuum is preset to run at approximately 3200-RPM (380), 3800-RPM (385), at no  
      load.  Do not slow engine down. 
4

.   SHUT OFF ALL ENGINES TO UNLOAD

5.  When operating tractor on slope or grade, exercise 

extreme caution

.  Do not cut across  

      grade or slope.  Mow directly up and down hills. 
6.  Periodically check all fasteners for tightness. 
7.  Listen for unusual vibration of engine or air turbine.  If excessive vibration is present, 

STOP

  

     

ALL ENGINES

 and check for damage to turbine fan. 

8.  Always shut off 

ALL ENGINES

 engine and vacuum engine before servicing. 

9.  Replace deflector shield when discharge chute is removed.  
10. When removing clogs, 

SHUT OFF ALL ENGINES

.  

Failure to do so can cause serious   

      bodily injury! 

 

EXTENDED STORAGE PROCEDURES 

 

1. Wash and clean vacuum and lubricate any lubrication points.  Grease wheel at axle 
   for longer life. 
2. Drain fuel from tank and run until fuel is exhausted in carburetor. 
3. Drain and change the engine oil. 
4. Clean tires and check pressure.  Raising and supporting unit with weight off tires is   
    recommended. 
5. When storing a unit with Rubbermaid® containers, leave containers latched to top.   

 

 

TRAC VAC WARRANTY POLICY 

 

 
 
 
 
 
 
 
 
 
 
 
 

MIDWEST EQUIPMENT MANUFACTURING, INC.-5225 Serum Plant Road.-Thorntown, IN 

46071 

Phone: 1-800-Trac-Vac 

Web Page: 

www.trac-vac.com

  E-Mail

[email protected]

 

Midwest Equipment Manufacturing, Inc. will repair or replace, free of charge, any part or part 
that are defective in material or workmanship or both for a period of one year residential use and 
90 days for commercial and rental use.  The purchaser will pay transportation charges on parts 
submitted for replacement under warranty.  For warranty service, contact your local dealer from 
whom the unit was purchased.  There are no other express or implied warranties.  Some states do 
not allow limitations on how long an implied warranty lasts, and some states do not allow the 
exclusion or limitation of incidental or consequential damages, so the above limitation and 
exclusion may not apply to you.  This warranty gives you specific legal rights and you may have 
other rights, which vary from state to state. 

Содержание 565CKG










Отзывы: