TPS WP-81 Скачать руководство пользователя страница 7

Страница: 7 / 51

Page 7

1.2 Unpacking Information

Before using your new

WP-81

, please check that the following

accessories have been included:

Part No

WP-81

Conductivity-TDS-Sal-pH-ORP-Temp instrument ....... 121132/1

...................................................................................................

121132/3

...................................................................................................

121132/5

2. Conductivity/ATC/Temperature Sensor:

k=1

1, 3 or 5m cable

(see cable label for part No)

k=10

1, 3 or 5m cable

k=0.1

1, 3 or 5m cable

3. pH Sensor:

(see cable label for part No)

1, 3 or 5m cable

4. Conductivity Standard, 200mL:

2.76 mS/cm ............... 122306

or 58.0 mS/cm ............... 122315

150.0 uS/cm ............... 122320

5. pH7.00 Buffer, 200mL ............................................................ 121387

6. pH4.01 Buffer, 200mL ............................................................ 121381

7. Battery charger ...................................................................... 130037

8. Manual

Options that may have been ordered with your

WP-81

1. Extended cable ...................................................................... 130040

2. RS232 Serial Interface Cable................................................. 130041

3. Communication software for Windows 95 and later ............... 130086

4. USB to Serial Adaptor (requires 130041 also) ....................... 130087

5. Hard Carry Case .................................................................... 130059

6. Battery charger lead for 12V cigarette lighter socket .............. 130046

7. Battery charger lead for 12V DC, with battery clips ................ 130052

8. Solar Panel ............................................................................ 130012

Содержание WP-81




















































Результаты поиска

Содержание WP-81

Отзывы:

TPS WP-81, Руководство пользователя, Страница: 7 / 51

Результаты поиска

Содержание WP-81

Отзывы: