TPS WP-81 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 51

TPS WP-81 Скачать руководство пользователя страница 22

Page 22

8.2 Failed Calibration

If calibration has failed, the GLP function will reset the date and time to
zero. The

WP-81

still shows the results of the last successful calibration.

For example…

Cond Zero 0.00uS
@ 00/00/00 00:00

k=1.00
@ 00/00/00 00:00

Asy 0.10pH
@ 00/00/00 00:00

Slope 100.0%
@ 00/00/00 00:00

Temp Offset 1.0

O

c

@ 00/00/00 00:00

Note that these calibration values are still used if further measurements
are taken without re-calibrating.

8.3 Printing GLP Information to the RS232 Port

The GLP information stored in the instrument’s memory can be sent to a
printer or PC via the RS232 port. Switch the meter on.

1. Ensure that the

WP-81

RS232 cable is connected to the instrument

and to the printer or PC.

2. Send the GLP information to the RS232 port.

(



F4:Setup



F3:GLP



F3:Print

)

3.

The GLP information is sent to the RS232 port in formatted ASCII
text. For

example…

WP81 V6.0 S1234 @ 30/03/11 12:00
Conductivity Zero= 0.00uS @ 30/03/11 11:00
Conductivity k= 1.00 @ 2.76mS @ 30/03/11 11:10
pH Asy= 0.00pH @ 30/03/11 11:40
pH Slope= 100.0% @ 30/03/11 11:50
Temperature Offset= 1.0oC @ 30/03/11 12:00
ENDS

«
...
20
21
22
23
24
...
»

Содержание WP-81




















































Отзывы:

Нет отзывов