TPS miniCHEM-Sal Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 31

background image

Page 17

10. When the reading has stabilised, adjust the

SPAN

control until the display

shows the value of the standard.

11. Rinse the Salinity/TDS sensor in distilled water and blot dry.

12. The

mini

CHEM

-Sal

is now calibrated and ready for Salinity/TDS

measurements.

4.2 Calibration Notes

1. The Zero calibration is quite stable long term, and only needs to be performed

monthly as a routine check. In applications where the sensor can become dirty
or coated with oils etc., a Zero calibration may need to be done weekly.

2. A Span calibration should be performed at least weekly. Of course, more

frequent calibration will result in greater confidence in results.

«
...
15
16
17
18
19
...
»

Содержание miniCHEM-Sal
































Отзывы:

Нет отзывов

Похожие инструкции для miniCHEM-Sal

Бренд: NEC Страницы: 72

400DX-2 - 40IN LCD 1920X1080 3000:1 VGA Dvi

Бренд: Samsung Страницы: 28

400DX-2 - 40IN LCD 1920X1080 3000:1 VGA Dvi

Бренд: Samsung Страницы: 29

Бренд: babymoov Страницы: 48

i3TOUCH Premium P6505 T10

Бренд: i3-TECHNOLOGIES Страницы: 15

Бренд: VARIZOOM Страницы: 2

Chino SHVSS Series

Бренд: Hussmann Страницы: 24

ProSeries 1 VS45130-0200

Бренд: Vitasigns Страницы: 28

Бренд: Rapid Controls Страницы: 55

Бренд: Elecrow Страницы: 6

Бренд: Dot-x Страницы: 12

Бренд: Acer Страницы: 24

Бренд: Safety Vision Страницы: 32

Бренд: Plusmed Страницы: 44

Бренд: Acer Страницы: 23

Бренд: Acer Страницы: 23

Бренд: Acer Страницы: 27

Бренд: Acer Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды