TPI Amp Plus 296 Скачать руководство пользователя страница 28

Страница: 28 / 32

F. MAINTENANCE

1. Battery Replacement:

The 296 will display a bat-

tery symbol when the internal 9 Volt battery needs
replacement. The battery is replaced as follows:

Disconnect and remove all test leads
from live circuits and from the 296.

Loosen the screw from the back of the
296 battery cover.

Remove the battery compartment cover.

Remove old battery and replace with new battery,
observing the correct polarity.

Reassemble the instrument in reverse
order from above.

2. Cleaning your 296:

Use a mild detergent and slightly damp cloth to
clean the surfaces of the 296.

l. Disable Sleep Mode

Set the 296 to the

OFF

position.

Push and hold down the

HOLD

button while

turning the rotary switch to the desired function.

Release the

HOLD

button.

Check the LCD to see if the HOLD function is
activated. If “H” is on the display, push the

HOLD

button to deactivate the DATA HOLD mode.

Sleep mode is now deactivated.

Standard Accessories

Part No.

9 Volt Alkaline Battery

A009A

Test Lead Set

A040

Soft Carrying Pouch

A200

Optional Accessories

Part No.

Deluxe Test Lead Set

SDK1C

IEC 1010 Deluxe Test Lead Kit

TLS2000BC

Hard Carrying Case

A201

*These accessories have not been evaluated by UL and are not
considered as part of the UL Listing of this product.

E. ACCESSORIES*

www.

.com

[email protected]

1.800.561.8187

All manuals and user guides at all-guides.com

Содержание Amp Plus 296

































Результаты поиска

Содержание Amp Plus 296

Отзывы:

Похожие инструкции для Amp Plus 296

Бренды по названию

Популярные бренды

TPI Amp Plus 296, Инструкция по эксплуатации

Результаты поиска

Содержание Amp Plus 296

Отзывы:

Похожие инструкции для Amp Plus 296

Бренды по названию

Популярные бренды