TPI 712 Скачать руководство пользователя страница 23

Страница: 23 / 29

Appendix C: ERROR CODES & TROUBLESHOOTING

Code

Displayed

Code Definition

Possible Causes

Corrective Action

Flo
Err

Pump not drawing sample at
correct flow rate.

Blockage / kink in flue probe
hose.

Dirty or blocked filter(s).

Worn pump.

Check and rectify. See
Appendix A.

Replace filter(s). See
Appendix A.

Return to TPI for service.

InIt

Err

Oxygen sensor failed to ini-
tialize

Flue probe connected to 712
prior to power up.

712 did not purge completely
from last sample.

Worn or defective oxygen
sensor.

Disconnect probe and
restart.

Purge for 20 minutes and
restart.

Return to TPI for sensor
replacement.

Try manually initializing the
sensor. See Appendix E.

InIt
CO
Err

Carbon monoxide sensor
failed to initialize.

Flue probe connected to 712
prior to power up.

712 did not purge completely
from last sample.

Worn or defective carbon
monoxide sensor.

Disconnect probe and
restart.

Purge for 20 minutes and
restart.

Return to TPI for sensor
replacement.

Try manually initializing the
sensor. See Appendix E.

bat

Low battery.

Battery needs to be charged. Charge battery. If the battery

won’t hold a charge, replace
the battery.

oFL

Overflow indication. The
pressure being measured is
outside the maximum mea-
surement capability.

Pressure being measured is
too high or low.

Pressure sensor damaged or
defective.

Remove pressure source.

Return to TPI for service.

oFL

Overflow indication. The tem-
perature being measured is
outside the maximum mea-
surement capability.

Temperature being measured
is too high or low.

Remove pressure source.

oPEn

Unable to read thermocouple
(temperature).

Temperature probe not con-
nected to input.
Worn temperature sensor.

Connect temperature probe
to analyzer.
Replace temperature probe
or flue probe.

Appendix B:

A773 SULFUR FILTER INSTALLATION & MAINTENANCE

4. Beginning on the “Flue Probe” side of the A773 sulfur filter, pull the yellow

thermocouple cord out of the channel of the flue probe tube. Pull out approx-
imately the length of the water trap that was removed.

5. Being careful not to cut the yellow cord, cut out a section of the flue probe

tubing the length of the water trap on the “Flue Probe” side of the A773 sul-
fur filter. (See picture below)

6. Install the water trap in the flue probe hose where the piece was cut out. Make

sure the water trap is positioned correctly. The water trap lid should face the
“Hose End” side of the hose.

A773 SULFUR FILTER MAINTENANCE:

The A773 should be replaced when most of the pellets become discolored, usual-
ly white or black.

If the A773 begins to trap condensate and fill with water but the pellets are not
discolored to the point replacement is required, it should be removed and allowed
to dry. Once it is dry it can be reused.

Содержание 712






























Результаты поиска

Содержание 712

Отзывы:

Похожие инструкции для 712

Бренды по названию

Популярные бренды

TPI 712, Руководство пользователя

Результаты поиска

Содержание 712

Отзывы:

Похожие инструкции для 712

Бренды по названию

Популярные бренды