TPI 291 Скачать руководство пользователя страница 6

Страница: 6 / 24

INTERNATIONAL SYMBOLS

CAUTION: RISK OF ELECTRIC SHOCK

AC (Alternation Current)

DC (Direct Current)

REFER TO INSTRUCTION MANUAL

GROUND

DOUBLE INSULATION

EITHER DC OR AC

C. TECHNICAL DATA

1. Features and Benefits

Agency

UL Listed to U.S. and Canadian
Safety Standards. Meets CE
and IEC 1010.

4000 Count

Improves the resolution on all
functions and ranges.

Data Hold

Maintains the reading on the
display for hard to reads areas.

Peak Mode

Measure the inrush current of
motors, relays and solenoids.

Sleep Mode

Automatically powers down
after 10 minutes of inactivity.

2. Product Applications

Perform the following tests and/or measurements with
the 291 and the appropriate function:

HVAC/R
ACA

• Heat anticipator current in thermostats.

ACV

• Line voltage.

ACV or DCV

• Control circuit voltage.

OHMS

• Heating element resistance (continuity).

OHMS

• Compressor winding resistance.

OHMS

• Contactor and relay coil resistance.

ACA

• Motor and compressor start up current.

OHMS

• Continuity of wiring.

ALL

• Bar graph to indicate rapid fluctuations.

ELECTRICAL
ACV

• Measure line voltage.

ACA

• Measure line current.

OHMS

• Continuity of circuit breakers.

DCV

• Voltage of direct drive DC motors.

ACA

• Start up current of motors, relays,

contactors and transformers.

ELECTRONIC
ACV

• Measure power supply voltage.

ACA

• Measure power supply current.

OHMS

• Continuity of circuit breakers and fuses.

Содержание 291

























Результаты поиска

Содержание 291

Отзывы:

Похожие инструкции для 291

Бренды по названию

Популярные бренды

TPI 291, Инструкция по эксплуатации

Результаты поиска

Содержание 291

Отзывы:

Похожие инструкции для 291

Бренды по названию

Популярные бренды