TPI Corporation 3900WW108 Скачать руководство пользователя страница 8

Страница: 8 / 15

INSTALLATION

INSTRUCTIONS

INSTALLATION INSTRUCTIONS
INBUILT DUPLEX RECEPTACLE

MODEL 3900REC

SAVE THESE INSTRUCTIONS

CAUTION:

Disconnect supply service to baseboard to avoid electrical shock.

All wiring connections must conform to the National Electric Code and local codes having jurisdiction.

NOTE:

The receptacle must be connected to a branch circuit other than the baseboard heater

circuit, having over current protection in accordance with National Electric Code.

1. The receptacle cover assembly can be mounted in the left or right hand junction box.

2. Remove the baseboard heater junction box cover and retain the screw.

3. Attach the 120V branch supply leads and ground lead to the receptacle. Use copper
conductors only.

4. Install receptacle cover assembly to the baseboard junction box and secure with previously
removed screw.

5. Restore power and check for proper operation.

8927 - REV. 110206

HEATER
SUPPLY

THERMAL CUTOUT

DUPLEX
RECEPTACLE

GND

ELEMENT

INSTALLATION

INSTRUCTIONS

IMPORTANT: OWNER SHOULD RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

Содержание 3900WW108
















Результаты поиска

Содержание 3900WW108

Отзывы:

Похожие инструкции для 3900WW108

Бренды по названию

Популярные бренды

TPI Corporation 3900WW108, Руководство по установке

Результаты поиска

Содержание 3900WW108

Отзывы:

Похожие инструкции для 3900WW108

Бренды по названию

Популярные бренды