TP-Link tl-wr845n Скачать руководство пользователя страница 62

Страница: 62 / 87

Chapter 4

•

IPv6 Address Prefix

- Display the IPv6 prefix length in dotted-decimal notation

provided by your ISP.

•

Default Gateway

- Display the default gateway in colon-hexadecimal notation

provided by your ISP.

•

Connect

- Click

Connect

to connect immediately.

•

Disconnect

- Click

Disconnect

to disconnect immediately.

•

Get IPv6 DNS Server Automatically

- If your ISP does not give you any DNS IPv6

address, keep the default selection

Get IPv6 DNS Server Automatically

, and the

DNS servers will be assigned from ISP dynamically.

•

Primary IPv6 DNS

- Enter the DNS IPv6 address in colon-hexadecimal

notation provided by your ISP.

•

Secondary IPv6 DNS

- Enter another DNS IPv6 address in colon-

hexadecimal notation provided by your ISP.

•

Use the following IPv6 DNS Servers

- If your ISP gives you one or two DNS IPv6

addresses, select

Use the following IPv6 DNS Servers

and enter the

Primary

IPv6 DNS

and

Secondary IPv6 DNS

in the corresponding fields.

Note:

If you get “Address not found error” when you access a web site, it is likely that your DNS servers are set up
improperly. You should contact your ISP to get DNS server addresses.

DHCPv6

•

IPv6 Address

- The IPv6 address assigned by your ISP dynamically.

•

Default Gateway

- Display the default gateway in colon-hexadecimal notation

provided by your ISP.

•

Renew

- Click

Renew

to renew the IPv6 parameters from your ISP.

•

Release -

Click

Release

to release the IPv6 parameters from your ISP.

Содержание tl-wr845n
























































































Результаты поиска

Содержание tl-wr845n

Отзывы:

Похожие инструкции для tl-wr845n

Бренды по названию

Популярные бренды

TP-Link tl-wr845n, Руководство пользователя

Результаты поиска

Содержание tl-wr845n

Отзывы:

Похожие инструкции для tl-wr845n

Бренды по названию

Популярные бренды