Standard
Protocol
Interface
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant
provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
Specifications
General Specifications
Network Media (Cable)
MAC Address Table
Switching Capacity
Transfer Method
MAC Address Learning
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Environmental and Physical Specifications
0
˚
C to 40
˚
C (32
˚
F to 104
˚
F)
-40
˚
C to 70
˚
C (-40
˚
F to 158
˚
F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3an
IEEE802.3bz, IEEE802.3x, IEEE802.1p
CSMA/CD
100BASE-TX:
2-pair UTP/STP of Cat. 5 or above (maximum 100 m)
1000BASE-T:
4-pair UTP/STP of Cat. 5e or above (maximum 100 m)
2.5GBASE-T:
4-pair UTP/STP of Cat. 5e or above (maximum 100 m)
5GBASE-T:
4-pair UTP/STP of Cat. 5e or above (maximum 100 m)
10GBASE-T:
4-pair UTP of Cat 6 (maximum 55 m) or STP of Cat 6,
6a, 7 (maximum 100 m)
5 100M/1G/2.5G/5G/10G RJ45 Ports
Auto-Negotiation/Auto MDI/MDIX
32K
100 Gbps
Store-and-Forward
Automatically learning, automatically aging
QoS (802.1p/DSCP), 802.3x flow control
100Base-TX: 148810 pps/port
1000Base-TX: 1488095 pps/port
2.5GBase-TX: 3720238 pps/port
5GBase-TX: 7440476 pps/port
10GBase-TX:14880952 pps/port
Q1. Why is the Power LED not lit?
Q2. Why are the right and left LEDs not lit when a device is
connected to the corresponding port?
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working
normally. If the Power LED is not lit, check as follows:
A1:
Make sure the power adapter is connected to the switch with
power source properly.
A2:
Make sure the voltage of the power supply meets the requirements
of the input voltage of the switch.
A3:
Make sure the power source is on.
It is recommended that you check the following items:
A1:
Make sure that the cable connectors are firmly plugged into the
switch and the device.
A2:
Make sure the connected device is turned on and works normally.
A3:
Make sure the cable category and length meet the standards listed
in General Specifications.
For technical support and other information, please visit
https://www.tp-link.com/support
, or simply scan the QR
code.
If you have any suggestions or needs on the product
guides, welcome to email
.
To ask questions, find answers, and communicate with TP-Link users
or engineers, please visit
https://community.tp-link.com
to join
TP-Link Community.
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Place the device with its bottom surface downward.
The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily
accessible.
Use only power supplies which are provided by manufacturer and in the origin packing of this
product. If you have any questions, please don’t hesitate to contact us.
Advanced Feature
Frame Forwarding Rate
