ENGLISH
2
CAUTION
• Ensure there is 30 cm of clear space on all sides of the unit.
(Fig. F)
• Remove drain water before moving unit.
• To minimize corrosion, DO NOT use in damp, salty air area.
• DO NOT operate in direct sunlight.
• DO NOT use for such particular purpose as preservation of
foodstuff, animals, plants, precision appliances, arts and med-
icine.
• DO NOT place an animal, plants or combustion equipment in
a place which is subjected to the direct air flow of the unit.
• DO NOT ride or place the objects on the unit.
• DO NOT turn the product on its side or upside down.
• Waste electrical products should not be dispose
with household waste.
• Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
3. OPERATION
OPERATING STEPS:
1. CONNECT POWER PLUG (A6) TO POWER SOCKET.
Make sure the water tank (B3) is placed in proper position, and
then connect to the power socket.
If the tank is not in proper position, the FULL lamp (C10) will
light after plug on. If FULL lamp lights at the first time, please
pull out the tank once and push it back to the proper position.
2. PRESS POWER BUTTON (C1) TO ON.
3. PRESS HUMIDITY SETTING BUTTON (C4)
Press the humidity setting button (C4) to set desired humidity
40%
➞
50%
➞
60%
➞
Cont. Cont. is indicated a continuous
dehumidification, dehumidification equipment without humidi-
ty setting, no humidity control. If the humid reduce to the set-
ting humidity ,the machine will stop automatically.
Example: in the dehumidification operation:
Set the 50%--- expectations of environmental humidity value
is 50%, when the appliance detects that the current environ-
ment humidity is higher than or equal to 52%RH, the appli-
ance start; when the appliance detects that the current envi-
ronment humidity is less than or equal to 48%RH, machine
stop dehumidification.
4. TIMER OPERATION
Press off timer button (C2) to set the working hour of units 2h
➞
4h
➞
6h
➞
No timer.
5. PRESS POWER BUTTON (C1) TO OFF.
4. EMPTY THE WATER TANK (Fig.D)
When the water tank is full, the full lamp (C10) will light and
the compressor will stop automatically. This will also stop
the dehumidification process.
• Empty the water tank and replace it in the correct posi
-
tion. (D2, D3) The dehumidifier will continue dehumidify-
ing when the compressor automatically starts after three
minutes.
5. CONTINUOUS DRAINAGE WATER (Fig. E)
If desired, it possible to connect the drainage hose (E1) to the
device for permanent water drainage. Connect the drainage
hose to the drain spout and ensure that the end of the hose is
lower than the drain opening, otherwise the water will not
drain and flooding may occur. (E2, E3, E4).
6. DEFROSTING
When the machine is in the environment of low tempera-
ture durying operation, the surface of the evaporator may
frost. In order to ensure the normal operation of the ma-
chine, machine is provided with an automatic defrosting
function.
7. MAINTENANCE & CLEANING
For its casing is made of plastic, do not place it in direct
sunlight.
Remove the water tank with care.
If not using the unit for a long time. Please switch off and
unplug the unit, empty the water reservoir, and pack it after
2 days, then, keep it in dry and ventilated place.
Only use a soft clean cloth for all cleaning purpose. Do not
use gasoline, paint thinner or other chemicals to clean the
unit.
Cleaning mesh filter: To remove the filter in arrow direction
(G1). Use a vacuum cleaner or water to clean (G2), then
put it in ventilated place until it's dry.
WARNING
• DO NOT touch the evaporator. It may cause injury or damage.
CAUTION
• DO NOT use over 40
°
C hot water. The plastic part may be de-
formed.
• Disconnect the power supply before cleaning and mainte
-
nance.
CLEANING SURFACE
Clean the outside of the product with a soft damp cloth.
8. TRANSPORTATION
Preferably keep the unit in the vertical position during transporta-
tion. If it is necessary to place the unit in a horizontal position more
than 1/2 hour, ALLOW IT TO REMAIN UPRIGHT FOR 24 HOURS
BEFORE OPERATION. Failure to do so may result in damage to the
compressor. Before transporting / moving the unit make sure the
drain tank is empty.
