Toyotomi TAD-T40LW, Инструкция по эксплуатации

Страница: 6 / 16

CAUTION
¡
ALWAYS store the unit in the vertical position.
¡
DO NOT put heavy objects on top of the unit.
7. TRANSPORTATION
Preferably keep the unit in the vertical position during transportation.
If this is not possible then lay it on its rear side, when at destination
put the unit back in the vertical position and wait at least ten (10)
minutes before using it. Before transporting/moving the unit make
sure the drain tank is empty.
8. TROUBLESHOOTING
BEFORE CALLING FOR SERVICE
The followings are not defects.
9. SPECIFICATIONS
NOTE: Cooling air capacity will vary according to temperature and
humidity of the room.
10.VENTING KIT ACCESSORIES
If the unit is to be used exclusively in one space, the cooling effi-
ciency will be enhanced by using the following venting kit acces-
sories.
EXHAUST DUCT SET (FLEXIBLE TUBE) (Fig. I)
2 pcs.
Max. 4 ft. (1.2 m)
WINDOW PANEL KIT "C" (Fig. J)
Window panel kit "C"
For sliding and double-hung windows
Max. 37 in. (94 cm)
Min. 28-1/4 in. (72 cm)
USING EXHAUST DUCT SET (Fig. I)
1. Extend one-side ends of the exhaust duct
hose (flexible tube) (I2) around 4 in.
(100mm).
2. Insert both ends of exhaust duct hose
(flexible tube) (I2) into exhaust duct hose
adapter nozzles (I1) by twisting clockwise
until it stops.
3. Fix one of the exhaust duct hose adapter nozzles onto the rear
outlet of the unit. This is completed by sliding the exhaust duct
hose adapter nozzle of the hose downwards over the exhaust
outlet of the unit, which will be assembled with the grooves on
the connector of the unit. (B2 or B7)
4. Extend the exhaust duct hose (I2) and close the window or door
as far as possible trapping the exhaust duct hose adapter noz-
zle (I1).
NOTE: Place the unit as close as possible to the window or door.
USING WINDOW PANEL KIT (Fig. J)
NOTE:
Window installations are possible by the use of the exhaust
duct set and window panel kit.
In case of twin duct type, always use the window panel kit
"C".
1. Fix the exhaust duct hose grille (J3) to the window panel with
four (4) screws. Make sure that the panel is extended so that
screws do not go into sliding portion of panel.
3
ENGLISH
A hissing noise or hollow
sound :
A squeaking noise :
Odor :
The unit does not start nor
change operation mode im-
mediately :
e
This sound is generated from the
refrigerant flowing within pipes.
e
This noise is generated from the
unit when it is expands or con-
tracts with temperature changes.
e
Such odor as tobacco, cosmetics,
or foods may accumulate in the unit.
e
To prevent overloading the com-
pressor motor, the unit will be
stopped for more than 3 minutes.
SYMPTOM
Unit does
not work.
Unit sudden-
ly stops dur-
ing in opera-
tion.
Unit runs in-
termittently.
Unit func-
tions but the
room is not
cooled.
Condensed
water is
spilled out
when moving
the unit.
CAUSE
- Power cut.
- The plug has been
plugged improperly.
- The full-tank indicator
is ON. Tank is full.
- Current leaking or
pressing test button of
LCDI plug.
- The indoor tempera-
ture has reached the
set temperature level.
- The preset time is up.
- The full-tank indicator
is ON. Tank is full.
- Malfunction.
- Surrounding tempera-
ture is too high or too
low.
- Exhaust duct hose is
blocked.
- Window or door is left
open in the room.
- There is heat source in
the room or too many
of people in it.
- Air intake grille is
clogged.
- Filter is too dirty.
- Temperature setting is
too high.
- The tank is nearly full.
SOLUTION
- Wait for power to be
supplied again.
- Plug in again.
- Remove the drain wa-
ter from the drain tank.
- Press reset button af-
ter solving the prob-
lem.
- Reset the temperature
level.
- Reset the timer.
- Remove the drain wa-
ter from the drain tank.
- Contact your dealer.
- Check the duct hose.
- Close all windows and
door.
- Move out any heat
source in the room.
- Clean the air intake
grille.
- Replace the filter.
- Lower the temperature
setting.
- Remove the drain plug
on the rear bottom of
the unit, drain off the
water then the unit will
be in operation auto-
matically.
MODEL TAD-T40LW
COOLING CAPACITY 14,000 BTU/H
HEATING CAPACITY 11,000 BTU/H
DEHUMIDIFYING CAPACITY 0.48 gal/h (1.8 L/H)
POWER SOURCE Single Phase 115V, 60Hz
POWER CONSUMPTION 1200 W
OPERATING CURRENT
(Cooling) 10.8 A
(Heating) 10.8 A
AIR FLOW (MAX.) 222 CFM (6.3 m
3
/m)
OPERATING TEMP. RANGE 64˚F~100˚F (18˚C~38˚C)
DIMENSIONS (WxHxD)
19-11/16" x 33-5/8" x 15-3/4"
(500 x 854 x 400 mm)
WEIGHT 77 Lbs. (35 kg)
COMPRESSOR ROTARY
REFRIGERANT R-410A
4 in.
TAD-T40LW (GB/ES/FR) 12.5.14 10:48 AM ページ 3