Toyota RS3200 PLUS, Руководство пользователя

Страница: 7 / 23

Page 6 TOYOTA RS3200 REMOTE KEYLESS Security system
TOYOTA RS3200 remote keyless Security system Page 15
OPERATION
ARMING THE RS3200 (except PASSIVE ARMING)
The system may be A
RMED
in several ways. Do one of the following:
Lock the doors with your key:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the trunk or hatch, if necessary.*
Insert the key into the door key switch and turn it toward the front of
the vehicle:
The S
TATUS
M
ONITOR
’
S
LED turns on for 30 seconds, then
starts flashing.
�
The system is now A
RMED
.
Lock the doors from inside the vehicle:
Remove the key from the ignition switch.
Open the driver’s or front passenger’s door.
Push the central lock switch.
Exit the vehicle, and close all the doors.*
Close the trunk or hatch, if necessary.* Then:
The S
TATUS
M
ONITOR
’
S
LED turns on for 30 seconds, then
starts flashing.
�
The system is now A
RMED
.
Lock the doors with the remote control:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors.*
Close the trunk or hatch, if necessary.*
Press the LOCK button on the remote control. Simultaneously:
The doors lock.
�
The vehicle’s tail and marker lights flash once.
�
The buzzer chirps once.
�
The S
TATUS
M
ONITOR
’
S
LED turns on for 30 seconds, then
starts flashing.
�
The system is now A
RMED
.
* The system will not A
RM
while any of the doors, trunk or hatch is open. However, when you press
the LOCK button when the trunk is open, the doors will lock; the system will arm 30 seconds
after the trunk is closed.
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
LIGHTS FOR
30
SECONDS
(
PRE
-
ARMING
)
THEN
FLASHES
(
SYSTEM IS
ARMED
)
� � �
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
PROGRAMMING
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not P
ASSIVELY
A
RM
. To change the system’s operation for P
ASSIVE
A
RMING
operation, as well as adjust the E
NTRY
D
ELAY
time, follow the procedure below. For more
information on this feature, please refer to page 8.
1. Before you begin:
Close all the doors, and the trunk or hatch.
Unlock all the doors with the inside lock switch.
Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
a. Using the remote control,
lock, then unlock the
doors 3 times .
b. Open the driver’s door.
b. Lock then unlock the
driver’s door inside lock
button
1 time .
a. Close , then Open the door:
2 times = P
ASSIVE
A
RMING
OFF
3 times = P
ASSIVE
A
RMING
ON ,
0 Sec. E
NTRY
D
ELAY
4 times = P
ASSIVE
A
RMING
ON ,
15 Sec. E
NTRY
D
ELAY
5 times = P
ASSIVE
A
RMING
ON ,
30 Sec. E
NTRY
D
ELAY
c. Lock, then unlock the
driver’s door inside lock
button
3 times .
d. The system locks the door
in 2 seconds; if this does
not happen, start over.
c. The system locks the door
in 2 seconds; if this does
not happen, start over.
Programming is now
complete.
e. Unlock the driver’s door
inside lock button.
THE BUZZER CHIRPS ONCE WHEN
THE SYSTEM IS REMOTE ARMED