manualshive.com logo in svg

Town & Country Fireplaces TC36.NG02CN, Инструкция по эксплуатации

Поделиться
Скачать
Town & Country Fireplaces TC36.NG02CN Скачать руководство пользователя страница 5

Fig. # 5

AIR DEFLECTOR 
SECURING 
SCREWS

Ember Material Placement

A large bag of ember material is shipped with 
the fi replace and needs to be installed to ensure 
optimum performance and fl ame appearance.

Pull apart the material into ember size pieces 
(approximately 1” squares) and gently place them 
into the burner pan. Do not compress, leave it loose 
for best performance. 

Fill the burner pan level with the top of the pan at 
rear, and gradually slope forward to the fi rebox fl oor 
at the front, covering both burner tubes. 

Place remaining ember material outside of the 
burner pan as desired to cover-up gas lines and 
brackets.

Note:  Ember material placement and amount will 
affect fl ame appearance. More ember material 
results in lower fl ame height. Add or remove as 
needed until desired fl ame affect. 

Fig. # 5b

GLOWING EMBERS

7.   Attach rear defl ector  to rear of grate 
 

using the two screws provided 

 

(Fig. # 5).

TC36.NG02CN 210411-16

5

Содержание TC36.NG02CN

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды