11
Operational Precautions
■
For prevention of damage
●
Wipe plastic areas such as the top unit and remote
control with a soft cloth tightly wrung out with water.
Dry cloth or tissue
●
Do not lean against the toilet lid.
■
Problem Prevention
●
Disconnect the power plug if there is a risk of
lightning.
●
A toilet seat cover or a toilet
lid cover cannot be used.
(The body sensors or
seat switch may not
function properly.)
●
Do not urinate on the top unit, toilet seat or wand.
(Doing so may cause a failure or discoloration.)
●
Do not apply strong forces to the control panel of
the remote control.
●
When using a toilet cleaner to clean the toilet,
wash it off within 3 minutes and leave the toilet
seat and toilet lid open.
•
Wipe off any cleaner that remains on the bowl unit.
(If vapor from a toilet cleaner enters the top unit,
it may cause a malfunction.)
●
Do not use the product with the toilet lid removed.
●
Do not expose to direct sunlight. (Doing so may cause
changes in color, irregular heated seat temperature,
remote control malfunction or NEOREST malfunction
due to the change in temperature.)
●
Use radios, etc. away from NEOREST. (The product
could cause interference with the radio signal.)
●
If you use a booster seat for infants or a soft
highchair, remove it after use. (Keeping it installed
may prevent some of the functions from being used.)
●
Do not apply force to the remote control.
(May cause malfunctions.)
To prevent the remote control from being dropped,
set it in the hanger when you are not using it.
Be careful not to expose it to water.
●
Do not place anything on the toilet seat and lid,
and do not press them with hands.
Failure to do so may turn on the seat switch,
causing the
fl
oor to get wet if buttons on the
remote control are touched and warm water
comes out from the wand. (The seat switch may
turn on if force is applied to the toilet seat or lid.)
■
For prevention of malfunctions
●
Do not block the body sensor or the remote control
transmitter or receiver.
< About the body sensors >
Two types of body sensors are used.
●
Body sensor A detects changes in heat.
Detection may be dif
fi
cult when the room temperature
exceeds 30°C, such as in the summertime.
When sunlight is directly on the sensor area or a heater is
used in the bathroom, the sensor may detect incorrectly
due to the heat, resulting in the automatic operation of
functions such as auto lid opening and closing.
When the bathroom door is open, the sensor may
detect people who pass to the front or side of the toilet.
●
Body sensor B detects when someone stands in front of the bowl unit.
Body sensor B emits an infrared beam as shown
in the
fi
gure. When someone moves into the line of
this infrared beam, the sensor detects the person.
* Detection by the sensor may be dif
fi
cult when the
toilet is used by someone small, such as a child.
Body sensor A
(Detects changes
in heat)
Body sensor B (Detects a person
standing in front of the bowl unit.)
< About the seat switch >
●
When you sit on the toilet seat, the seat switch turns
ON, enabling you to use various features. (A click
sound is heard when the seat switch is ACTIVATED.)
Seat switch (Built-in)
Gap
The toilet seat lowers.
Switch
ON
●
Sit back on the toilet seat.
The seat switch will
not turn on unless
you sit on the seat
properly.
Note
When a child uses the product, the seat switch
may not be ACTIVATED by their light body weight.
Since the toilet seat is designed to move up
and down, a clearance is provided between
the toilet seat cushion and the bowl unit.
Covers
Introduction
M08009_HK_AH(EN)_CS5.indd 11
M08009_HK_AH(EN)_CS5.indd 11
7/8/2015 8:13:09 AM
7/8/2015 8:13:09 AM
