Toshiba TPS0A0700AXA страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 41

background image

TPX Series UPS 700VA Operational Manual

– 97673-000

25

13. INSTALLATION PRECAUTIONS

1. Install the unit in a well-ventilated location; allow at least 4 inches (10 cm) between the

rear panel and the wall for air ventilation.

2. Install the unit in a stable, level and upright position that is free of excessive vibration.

3. Install the unit where the ambient temperature is within the range specified.

4. Do not install the UPS in areas that are subject to high humidity.

5. Do not install the UPS in areas that allow exposure to direct sunlight.

6. Do not install the UPS in areas that allow exposure to high levels of airborne dust, metal

particles, or flammable gases.

7. Do not install the UPS in areas near sources of electrical noise. Ensuring a proper earth

ground will reduce the effects of electrical noise and will reduce the potential for electrical

shock.

8. Do not install the UPS in areas that would allow fluids or any foreign object to get inside

the UPS.

CAUTION

«
...
31
32
33
34
35
...
»

Содержание TPS0A0700AXA










































Отзывы:

Нет отзывов

Похожие инструкции для TPS0A0700AXA

Бренд: Eaton Страницы: 27

LINE UPS Series

Бренд: bitmore Страницы: 32

Бренд: Eaton Страницы: 186

Бренд: Tripp Lite Страницы: 24

Бренд: Tripp Lite Страницы: 116

Бренд: Powertronix Страницы: 33

SmartPro SMART1500

Бренд: Tripp Lite Страницы: 6

SmartPro Rackmount SMX500RT1U

Бренд: Tripp Lite Страницы: 5

SmartPro AGSM1050PJR3

Бренд: Tripp Lite Страницы: 6

SmartPro 2200XLT

Бренд: Tripp Lite Страницы: 8

SmartPro AGSM152DRTi2U

Бренд: Tripp Lite Страницы: 13

SmartPro 3U Rackmount 5000 VA

Бренд: Tripp Lite Страницы: 25

SmartPro Rackmount

Бренд: Tripp Lite Страницы: 40

SmartPro AG-0018

Бренд: Tripp Lite Страницы: 48

SmartPro Rackmount SMX3000XLRT2U

Бренд: Tripp Lite Страницы: 76

LEONARDO RT 10 kVa

Бренд: Borri Страницы: 52

INGENIO COMPACT

Бренд: Borri Страницы: 134

PW 1000/LT Series

Бренд: Kohler Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды