Toshiba TD-E432 Скачать руководство пользователя страница 12

Страница: 12 / 80

all pixels displaying white at center 5 location.

The variation in surface luminance, _WHITE is defined (center of Screen) as:

HITE(9P)= Minimum(Lon1, Lon2,…,Lon9)/ Maximum(Lon1, Lon2,…Lon9)

Response time Tr is the average time required for display transition by switching the input signal for five

luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=60Hz to optimize.

The response time is defined as the following figure and shall be measured by switching the input

signal for

“any level of grey(bright) “ and “any level of gray(dark)”.

Any level of gray (Bright) Any level of gray (Dark) Any level of gray

(Bright)

FIG. 2 Luminance

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are

determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is

normal to the LCD surface. For more information see FIG3.

Содержание TD-E432

















































































Результаты поиска

Содержание TD-E432

Отзывы:

Похожие инструкции для TD-E432

Бренды по названию

Популярные бренды

Toshiba TD-E432, Руководство по обслуживанию

Результаты поиска

Содержание TD-E432

Отзывы:

Похожие инструкции для TD-E432

Бренды по названию

Популярные бренды