DK14 Installation
DK14 Wiring Diagrams
Strata DK I&M 6/00
1-23
DK14 Installa
ti
on
DK14 Wiring Diagrams
Wiring diagrams for the DK14 (listed below) are shown in
♦
DK14 MDF to Station Wiring (QCDU2 and QSTU2)
♦
DK14 MDF Wiring to CO Lines (KSU and QCDU)
♦
DK14 MDF Wiring to Caller ID Interface (WSIU)
Figure 1-15 DK14 MDF to Station Wiring (QCDU2 and QSTU2)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
W-BL
BL-W
W-O
O-W
W-GN
GN-W
W-BR
BR-W
W-S
S-W
R-BL
BL-R
R-O
O-R
R-GN
GN-R
R-BR
BR-R
R-S
S-R
BK-BL
BL-BK
BK-O
O-BK
BK-GN
GN-BK
BK-BR
BR-BK
BK-S
S-BK
Y-BL
BL-Y
Y-O
O-Y
Y-GN
GN-Y
Y-BR
BR-Y
Y-S
S-Y
V-BL
BL-V
V-O
O-V
V-GN
GN-V
V-BR
BR-V
V-S
S-V
26
1
27
2
28
3
29
4
30
5
31
6
32
7
33
8
34
9
35
10
36
11
37
12
38
13
39
14
40
15
41
16
42
17
43
18
44
19
45
20
46
21
47
22
48
23
49
24
50
25
Bridging Clips
To Base Unit (P5) With
Female Connector
Circuit 2 to DKT2
3
or PDIU-DS or DDCB
Circuit 3 to DKT3
3
or PDIU-DS or DDCB
Circuit 4 to DKT4
3
or PDIU-DS
Circuit 6 to DKT6
4
or PDIU-DS
Circuit 7 to DKT7
4
or PDIU-DS
Circuit 5 to DKT5
4
or PDIU-DS
(-) T1 (Voice /Data)
3
(GND) R1 (Voice /Data)
(-) PT1 (Add. Power)
(GND) PR1 (Add. Power)
T2
R2
PT2
PR2
T3
R3
PT3
PR3
T4
R4
PT4
PR4
T5
R5
PT5
PR5
T6
R6
PT6
PR6
T7
R7
PT7
PR7
Not Used
Station Cabling
Modular
Cord
Standard Telephone
Circuit 1
Not Used
QSTU2
Standard Telephone
Circuit 2 or BGM
R1
T1
R1
T1
Circuit 8 to DKT8
4
or PDIU-DS
T8
R8
PT8
PR8
Relay Contacts
25-PAIR CABLE W/MALE AMP CONNECTOR
66M150 Split Block
Not Used
Jacketed Twisted Pairs
24AWG (1 or 2 Pair, See Note 2)
GN
6 5 4 3 2 1
Y
BL
R
BK
W
3 4
R1
PT1
T1
PR1
2
5
PR TR PT
Digital Telephone (DKT 1)
(with or without ADM,
PDIU-DI/PDIU-DI2)
GND
PR
(-)
T
GND
R
(-)
PT
RJ11
2405
QCDU2
Notes
1. Voltage levels:
T, PT=-26.3~27.8 VDC
R PR=+4.5~+5.5 VDC
+5V converter on KSU PCB
2. T/R wires are always required: PT/
PR are additional power wires
required for long station runs only.
PT/PR can also be used with normal
station runs.
3. DKT circuits (1~4) are standard on
the DK14 main PCB.
4. DKT circuits (5~6) require one
optional QCDU2 circuit and DKT
circuits (7~8) require a second
QCDU2 to be installed.
Содержание Strata AirLink DK40i
