Toshiba Satellite U300 Скачать руководство пользователя страница 234

Страница: 234 / 361

Replacement Procedures

Installing the LCD unit/FL Inverter

The following describes the procedure for installing the LCD unit and FL inverter (See
Figure 4-31 to 4-34).

Install the LCD supports (LCD unit side) to the LCD and secure them with the
following

screws

•

M2.0

3.0 BINK screw

Stand the

LCD unit

on the display cover and connect the

LCD harness

to the

connector on the back of LCD.

Stick the

conductive tape

on the connector of LCD harness.

Secure the LCD unit with the following

screws

•

M2.5

4.0

BINK

screw

Connect

LCD harnesses

to the connector

CN1

of the FL inverter.

CAUTION: Be careful not to connect the LCD harnesses to the wrong connectors of FL

inverter.

Connect

HV harnesses

to the connector

CN2

of the FL inverter.

Install the

display mask

while fitting the latches.

Secure the display mask with following

screws

M2.5

6.0

BIND screw X4

Cover screws with Screw rubber cover X4

NOTE: When installing the display mask, make sure there is no gap between the display

mask and the display cover.

4-56Satellite U300 and Satellite Pro U300 Maintenance Manual (960-Q08)

Содержание Satellite U300










































































































































































































































































































































































Результаты поиска

Содержание Satellite U300

Отзывы:

Похожие инструкции для Satellite U300

Бренды по названию

Популярные бренды

Toshiba Satellite U300, Руководство по обслуживанию

Результаты поиска

Содержание Satellite U300

Отзывы:

Похожие инструкции для Satellite U300

Бренды по названию

Популярные бренды