Toshiba Satellite U300 Скачать руководство пользователя страница 211

Страница: 211 / 361

Replacement Procedures

Installing the display assembly

The following describes the procedure for installing the display assembly (See Figure 4-13 to
4-17).

Inserting the

pole

of hinge

to the

hole

of hinge assembly, set the

display assembly

on the base assembly.

Secure the

hinges

with the following

screws ,

Secure the

display mask

with the

following

screws

and stick the

mask seal

on them.

•

M2.5

6.0B

FLAT BIND screw

(Locktight)

NOTE: Be sure to apply the locktight to the screws instructed in the figure above.

Connect the

LCD harness

to the connector on the system board.

Arrange the wireless antenna cables along the guide (front) and secure them with

guide

Pass the cables to the back of computer through the

slot

Install the keyboard and k/b cover of the system.

Arrange the

wireless LAN antenna and Bluetooth cables

along the guide and

contact with the connector.

Secure the display assembly from the back of computer with the following

screws

•

M2.5

6.0B

FLAT BIND screw

(Locktight)

Satellite U300 and Satellite Pro U300 Maintenance Manual (960-Q08) 44

Содержание Satellite U300










































































































































































































































































































































































Результаты поиска

Содержание Satellite U300

Отзывы:

Похожие инструкции для Satellite U300

Бренды по названию

Популярные бренды

Toshiba Satellite U300, Руководство по обслуживанию

Результаты поиска

Содержание Satellite U300

Отзывы:

Похожие инструкции для Satellite U300

Бренды по названию

Популярные бренды