Toshiba Satellite R830 Скачать руководство пользователя страница 118

Страница: 118 / 515

Tests and Diagnostics

PORTEGE R830 Satellite R830 Series Maintenance Manual (960-880)

[CONFIDENTIAL] 3-9



A USB cable (USB test)



LAN wraparound connector (LAN test)



RGB wraparound connector (Expansion test)



Module cable and RJ11 connector checker (Modem test)



Headphones (Sound test)



A microphone (Sound test)



A PC for wraparound test (Wireless LAN test/Bluetooth test/IEEE1394 test)



PC card wraparound connector (Expansion test) [Not necessary for this model)

3.1.2 H/W (Hardware) initial information setting tool

The H/W initial information setting tool consists of the following programs.



Initial configuration



DMI information save



DMI information recovery



System configuration display



E2PROM test (MAC/GUID/DMI)

You will need the following equipment to perform some of the programs.



The Diagnostics Disk (Main T&D)

3.1.3 Heatrun test program

The heatrun test starts automatically after the selection.

You will need the following equipment to perform this program.



The Diagnostics Disk (Main T&D)

Содержание Satellite R830




































































































































































































































































































































































































































































































































Результаты поиска

Содержание Satellite R830

Отзывы:

Похожие инструкции для Satellite R830

Бренды по названию

Популярные бренды

Toshiba Satellite R830, Руководство по обслуживанию

Результаты поиска

Содержание Satellite R830

Отзывы:

Похожие инструкции для Satellite R830

Бренды по названию

Популярные бренды