Toshiba Satellite A350 Series Скачать руководство пользователя

Страница: 239 / 297

4 Replacement Procedures

Error! Style not defined. Error! Style not defined.

4.27

Bluetooth Card

Removing the Bluetooth card

Remove the Bluetooth card according to the following procedures and Figure 4.47.

Remove the Bluetooth cable from the Bluetooth card.

Press down the latch and push the Bluetooth card in the direction indicated in the figure
4.47 and slide the Bluetooth card out.

Remove the card from the logic lower assembly.

Figure

47 Removing the Bluetooth card

Note: Be careful not to damage the Bluetooth Card when connecting it with the cable. Make
sure the card is seated in the correct position.

Satellite A350D Maintenance Manual

4-62

Downloaded from LpManual.com Manuals

Содержание Satellite A350 Series










































































































































































































































































































Результаты поиска

Содержание Satellite A350 Series

Отзывы:

Похожие инструкции для Satellite A350 Series

Бренды по названию

Популярные бренды

Toshiba Satellite A350 Series, Руководство по обслуживанию

Результаты поиска

Содержание Satellite A350 Series

Отзывы:

Похожие инструкции для Satellite A350 Series

Бренды по названию

Популярные бренды