The FOLLOW ME function enables the
remote control to measure the temper-
ature at its current location. When using
AUTO, COOL, or HEAT functions,
measuring ambient temperature from
the remote control (instead of from the
indoor unit itself) will enable the air
conditioner to optimize the temperature
around you and ensure maximum comfort.
1. Press
button to activate
function. The remote control will send
temperature signal to the indoor unit
every three minutes.
2. Press
button again to
turn off this function.
FOLLOW ME
FOLLOW ME
The TURBO function makes the unit work
extra hard to reach your present temperature
in the shortest amount of time possible.
When you press the
button in
COOL mode, the unit will blow cool air
with strongest wind setting to jump-start
the cooling process.
TURBO
When you press the
button in
HEAT mode, for units with Electric heat
elements, the Electric Heater will activate
and jump-start the heating process.
TURBO
Airborne bacteria can grow in the moisture that
condenses around heat exchanger in the unit.
With regular use, most of this moisture is
evaporated from the unit. By pressing the
button, your unit will clean itself
automatically. After cleaning, the unit will turn
off automatically. Pressing the
button
mid-cycle will cancel the operation and turn
off the unit.
CLEAN
CLEAN
You can use
as often as you like.
CLEAN
You can only activate this function
in COOL or DRY mode.
Note:
FOLLOW ME function
SHORTCUT function
(RG57A3(B)/BGEF model only)
SWING function
SELF CLEAN function
TURBO function
SLEEP Function
The SLEEP function is used to decrease
energy use while you sleep (and don t need
the same temperature settings to stay
comfortable). This function can only be
activated via remote control.
Note:
The SLEEP function is not available
in FAN or DRY mode.
,
Used to restore the current settings or resume
previous settings.
Push this button when remote controller is on, the
system will automatically revert back to the
previous settings including operating mode, setting
temperature, fan speed level and sleep feature
(if activated).
If pushing more than 2 seconds, the system will
automatically restore the current operation settings
including operating mode, setting temperature, fan
speed level and sleep feature(if activated ).
Swing
Button
Swing
Button
Used to stop or start horizontal louver movement
or set the desired up/down air flow direction. The
louver changes 6 degree in angle for each press.
If keep pushing more than 2 seconds, the louver
will swing up and down automatically.
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press. If keep pushing more than 2
seconds, the vertical louver auto swing feature
is activated.
How To Use The Advanced Functions
How To Use The Advanced Functions
ON/OFF
ON/OFF
TEMP
TEMP
SHORT
CUT
TIMER
ON
TIMER
ON
TIMER
OFF
TIMER
OFF
MODE
MODE
FAN
FAN
SLEEP
SLEE P
TURBO
TURBO
CLE AN
CLEAN
LED
LED
FOLLOW
FOLLOW
FRESH
FRESH
ECO function
(RG57A8(B)/BGEF model only)
Used to enter the energy efficient mode.
Under cooling mode, press this button,
the remote controller will adjust the
temperature automatically to 24 C, fan
speed of Auto to save energy(but only
if the set temperature is less than 24 C).
If the set temperature is above 24 C ,
press the ECO button, the fan speed
will change to Auto, the set temperature
will remain unchanged.
O
O
O
Pressing the ECO button, or modifying
the mode or adjusting the set temperature
to less than 24 C will stop ECO operation.
Under ECO operation, the set temper-
ature should be 24 C or more. it may
result in insufficient cooling. If you feel
uncomfortable, just press the ECO
button again to stop it.
NOTE:
O
O
ECO
MODEL:RG57A8(B)/BGEF
MODEL:RG57A3(B)/BGEF