background image

– 10 –

EN

6

Operating unit with timer

ON timer and OFF timer

Setting TIMER

Set the timer during operation. The timer cannot be set if 
the air conditioner is not running.

1

ON/OFF TIMER button (  or  )

Push the ON or OFF TIMER buttons as required.
• The previous timer setting is displayed and 

flashes along with ON/OFF timer display.

Set the timer to the desired time.
Each push of the TIMER button changes the time in 
ten minute steps.
Pushing the TIMER button continually changes the 
time in one hour step.

2

SET  

button

Push the SET 

 button to set the timer.

The timer time is indicated and the timer starts.

Cancelling TIMER

3

CLR  

button

Push the CLR 

 button to cancel the timer setting.

CAUTION

• When you select the timer operation, the remote 

controller automatically transmits the timer signal to 
the indoor unit at the specified time. Therefore, keep 
the remote controller in a location where it can 
transmit the signal to the indoor unit properly. 
Otherwise, the time lag of up to 15minutes will occur.

• If you do not push the SET 

 button within 30 

seconds after setting the time, the setting will be 
cancelled.

Once you select the timer operation mode, the settings 
are saved in the remote controller.
Thereafter, the air conditioner will start operating under 
the same conditions when you simply push the ON/OFF 
button of the remote controller.

If the clock display is flashing, you cannot set the timer.
Follow the instructions in the section “Setting the clock” 
and then set the timer.

Combined timer (Setting both ON and 
OFF timers simultaneously)

OFF timer —> ON timer

(Operation —> Stop —> Operation)

This feature is useful when you want to stop the air 
conditioner after you go to sleep, and start it again in the 
morning when you wake up or you return home.
Example:
To stop the air conditioner and start it again next morning.

Setting combined TIMER

1. Push the OFF TIMER   button to adjust the 

OFF timer.

2. Push the ON TIMER   button to adjust the 

ON timer.

3. Push the SET 

 button.

CLR

SLEEP

SET

TEMP

3
2

1

ON

OFF

SET

SET

CLR

CLR

SET

Operation

Operation again

Stop

OFF

ON

SET

10-EN

+EH99950501.BOOK  Page 10  Thursday, June 18, 2015  10:57 AM

Содержание RBC-AX32UW-UL

















Отзывы: