Toshiba RAV-HM301MUT-E Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 115

background image

– 39 –

No.

24

Item

Soft cooling

Outline of specifications

* Wired remote controller : RBC-AMSU5

∗

is required.

1) Sensation of draft can be suppressed by controlling
performance and correcting the louver angle during cooling
operation.
2) However, it may not cool well because the operation will be
performed with the cooling capacity suppressed.
3) Perform operations from the remote controller menu to use
soft cooling.

This function cannot be
used with remote
controllers that are not
RBC-AMSU5

∗

.

25

Dual set point
(AUTO mode)

1) The temperature for heating operations and cooling
operations can be set separately in AUTO mode when dual
set point is valid.
2) The compressor will turn off (thermostat-OFF) when
reaching the set temperature for heating operations and
cooling operations.
3) Set CODE No. (DN) [77] to enable Dual set point.

Remarks

DN [77]

Data

Dual set point

0000

Unavailable (Factory default)

0002

Available

DN [121]

Data

Draft prevention control

0000

Unavailable

0001

Available (Factory default)

26

Fan speed
setting when
thermostat-OFF
in cooling
mode

1) The fan speed for when the room temperature reaches the
set temperature in cooling operations and dry mode can be
set.
2) Change the fan speed by operating CODE No. (DN)[9A].
3) Select “Remote controller setting” if changing fan speed is
not desired during thermostat-OFF.

* When selecting “0002” (OFF), make sure to use the Remote
controller sensor or Remote sensor unit so that the room
temperature can be detected properly.

27

Draft prevention
control

1) This function prevents cold air from descending from the air
outlet of the air conditioner when defrosting operations are
being performed and the indoor unit fan is stopped, by
closing the louver.
2) Valid/Invalid can be switched by CODE No. (DN) [121].
3) When defrosting operations start at the outdoor unit, the
indoor fan will stop since the temperature that the TC/TCJ
sensor detects falls and the cold air draft prevention control
is performed (see Item 7). When this function is valid, the
louver will close.
4) After the defrosting operations end and normal heating
operations start, causing the temperature that the TC/TCJ
sensor detects to rise and the indoor fan to start operations,
the louver will open at a horizontal angle, and thereafter
move to the point that is set by the remote controller.

DN [9A]

Data

Fan speed when thermostat-OFF

in cooling mode

0000

Remote controller setting

0002

OFF

0003

Low speed (L)

0001

Extremely low speed (UL)

(Factory default)

«
...
37
38
39
40
41
...
»

Содержание RAV-HM301MUT-E




















































































































Отзывы:

Нет отзывов

Похожие инструкции для RAV-HM301MUT-E

VRV FXZQ07MVJU9

Бренд: Daikin Страницы: 27

LI036CI-180P432

Бренд: Lennox Страницы: 100

Бренд: Taurus Страницы: 48

Бренд: York Страницы: 44

Бренд: EarthLinked Страницы: 11

Бренд: Carrier Страницы: 4

Бренд: Daikin Страницы: 44

Бренд: ECG Страницы: 104

Pure Airbox Home 500 S

Бренд: Zonair3D Страницы: 52

Бренд: Farelek Страницы: 76

Бренд: Coway Страницы: 24

Бренд: Amana Страницы: 32

Airmaster WOZ2000

Бренд: Wood’s Страницы: 72

Бренд: FASANO TOOLS Страницы: 8

Бренд: ARDES Страницы: 20

Бренд: Daikin Страницы: 64

Бренд: TripleAqua Страницы: 50

Бренд: Haier Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды