Toshiba RAS-13N3AV-E Скачать руководство пользователя страница 53

Страница: 53 / 105

– 52 –

FILE NO. SVM-12039

<When the installation plate is directly mounted on

the wall>

Securely fit the installation plate onto the wall by

screwing it in the upper and lower parts to hook up

the indoor unit.

To mount the installation plate on a concrete wall

with anchor bolts, utilize the anchor bolt holes as

illustrated in the above figure.

Install the installation plate horizontally in the wall.

CAUTION

When installing the installation plate with a

mounting screw, do not use the anchor bolt hole.

Otherwise the unit may fall down and result in

personal injury and property damage.

Projection

15 mm or less

Clip anchor

(local parts)

5 mm dia. hole

Anchor

bolt

Fig. 10-3-4

Mounting

screw

∅

4 x 25

CAUTION

Failure to firmly install the unit may result in

personal injury and property damage if the unit falls.

•

In case of block, brick, concrete or similar type

walls, make 5 mm dia. holes in the wall.

•

Insert clip anchors for appropriate

mounting

screws.

NOTE

•

Secure four corners and lower parts of the

installation plate with 4 to 6 mounting screws to

install it.

Installation plate

<Keep horizontal direction>

<How to connect the connecting cable>
Wiring of the connecting cable can be carried out

10-3-3. Wiring connection

1. Remove the air inlet grille.

Open the air inlet grille upward and pull it toward you.

2. Remove the terminal cover and cord clamp.

3. Insert the connecting cable (according to the local

cords) into the pipe hole on the wall.

4. Take out the connecting cable through the cable slot

on the rear panel so that it protrudes about 20 cm

from the front.

5. Insert the connecting cable fully into the terminal

block and secure it tightly with screws.

6. Tighten firmly but not over 1.2 N.m (0.12 kgf.m)

7. Secure the connecting cable with the cord clamp.

CAUTION

•

Be sure to refer to the wiring system diagram

labeled inside the front panel.

•

Check local electrical cords and also any specific

wiring instructions or limitations.

•

Wire type : More than H07RN-F or 60245 IEC66

•

Use stranded wire only.

NOTE

(1.0 mm

or more)

Fig. 10-3-5

without removing the front panel.

8. Fix the terminal cover, rear plate bushing and air

inlet grille on the indoor unit.

Stripping length of the connecting cable

Screw

Terminal cover

Cord clamp

Terminal block

Earth line

Screw

100 mm

10 mm

90 mm

Connecting cable

about 2

0 cm

Содержание RAS-13N3AV-E










































































































Результаты поиска

Содержание RAS-13N3AV-E

Отзывы:

Похожие инструкции для RAS-13N3AV-E

Бренды по названию

Популярные бренды

Toshiba RAS-13N3AV-E, Руководство по обслуживанию

Результаты поиска

Содержание RAS-13N3AV-E

Отзывы:

Похожие инструкции для RAS-13N3AV-E

Бренды по названию

Популярные бренды