manualshive.com logo in svg

Toshiba Qosmio G40, Руководство по обслуживанию


Поделиться
Скачать
background image

2  Troubleshooting Procedures 

2.6 2.5” HDD Troubleshooting 

2-44 

 [CONFIDENTIAL] 

QOSMIO G40 Maintenance Manual (960-632) 

Procedure 2 

Message Check 

When the power is turned on, the system performs the Initial Reliability Test (IRT) installed 
in the BIOS ROM. When the test detects an error, an error message is displayed on the screen. 

Make sure no floppy disk is in the FDD. Turn on the computer and check the message on the 
screen. When an OS starts from the 2.5” HDD, go to Procedure 3. Otherwise, start with 
Check 1 below and perform the other checks as instructed. 

Check 1  If any of the following messages appear, go to Procedure 3. If the following 

messages do not appear, perform Check 2. 

HDC ERROR

 

 

or 

HDD #X ERROR

     

(After 5 seconds this message will disappear.)

  

Check 2  If either of the following messages appears, go to Check 3. If the following 

messages do not appear, perform Check 4. 

Insert system disk in drive 
Press any key when ready ..... 

or 

Non-System disk or disk error 

Replace and press any key when ready

 

Check 3  Using the SYS command of the DOS, transfer the system to the 2.5” HDD. If the 

system is not transferred, go to Procedure 3. Refer to the DOS Manual for detailed 
operation. 

If the following message appears on the display, the system program has been 
transferred to the HDD. 

System Transferred 

If an error message appears on the display, perform Check 4. 

Check 4  2.5” HDD(s) and the connector(s) of system board may be defective (Refer to the 

steps described in Chapter 4, 

Replacement Procedures

 for disassembling.). Insert 

HDD(s) to the connector(s) firmly. If it is (or they are) firmly connected, go to 
Procedure 3. 

Downloaded from LpManual.com Manuals

Содержание Qosmio G40











































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Qosmio G40

Gateway M685 Setup preview
M685
Бренд: Gateway Страницы: 1
Logik LUPAUSL13E Instruction Manual preview
LUPAUSL13E
Бренд: Logik Страницы: 52
Oregon Scientific Barbie B-Glam LC68-12 Manual preview
Barbie B-Glam LC68-12
Бренд: Oregon Scientific Страницы: 2
Clevo M400A Service Manual preview
M400A
Бренд: Clevo Страницы: 99
Hyundai HY book plus User Manual preview
HY book plus
Бренд: Hyundai Страницы: 24
HP TouchSmart tx2-1000 - Notebook PC User Manual preview
TouchSmart tx2-1000 - Notebook PC
Бренд: HP Страницы: 30
HP TouchSmart tx2-1300 - Notebook PC User Manual preview
TouchSmart tx2-1300 - Notebook PC
Бренд: HP Страницы: 31
HP TouchSmart tx2-1000 - Notebook PC Maintenance And Service Manual preview
TouchSmart tx2-1000 - Notebook PC
Бренд: HP Страницы: 123
HP TouchPad and Keyboard User Manual preview
TouchPad and Keyboard
Бренд: HP Страницы: 236
Dell Latitude 5300 Service Manual preview
Latitude 5300
Бренд: Dell Страницы: 123
Dell Latitude 5414 Getting Started Manual preview
Latitude 5414
Бренд: Dell Страницы: 106
Panasonic Toughbook C2 Specification preview
Toughbook C2
Бренд: Panasonic Страницы: 2
Panasonic Toughbook C1 Brochure preview
Toughbook C1
Бренд: Panasonic Страницы: 2
Panasonic Toughbook 74 Brochure preview
Toughbook 74
Бренд: Panasonic Страницы: 2
Panasonic The Toughbook 52 Specifications preview
The Toughbook 52
Бренд: Panasonic Страницы: 2
Panasonic The Toughbook 52 Brochure preview
The Toughbook 52
Бренд: Panasonic Страницы: 2
Panasonic CF52PFNBEPM Brochure preview
CF52PFNBEPM
Бренд: Panasonic Страницы: 2
Panasonic Toughbook CF-18 mk3 Supplementary Instructions Manual preview
Toughbook CF-18 mk3
Бренд: Panasonic Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды