manualshive.com logo in svg

Toshiba Portege Z830, Руководство по обслуживанию


Поделиться
Скачать
background image

   

  Troubleshooting Procedures  

PORTEGE Z830 Satellite Z830 Series Maintenance Manual (960-883)  [CONFIDENTIAL]

 2-37 

2.6.2  Procedure 2 Message Check 

When the power is turned on, the system performs the Initial Reliability Test (IRT) installed 
in the BIOS ROM. When the test detects an error, an error message is displayed on the screen. 

Make sure no floppy disk is in the FDD. Turn on the computer and check the message on the 
screen. When an OS starts from the 2.5” HDD, go to Procedure 3. Otherwise, start with Check 
1 below and perform the other checks as instructed. 

Check 1 

If any of the following messages appear, go to Procedure 3. If the following 
messages do not appear, perform Check 2. 

HDC ERROR

 

 

or 

HDD #X ERROR

     

(After 5 seconds this message will disappear.)

  

Check 2 

If either of the following messages appears, go to Check 3. If the following 
messages do not appear, perform Check 4. 

Insert system disk in drive 
Press any key when ready ..... 

or 

Non-System disk or disk error 
Replace and press any key when ready

 

Check 3 

Using the SYS command of the DOS, transfer the system to the 2.5” HDD. If the 
system is not transferred, go to Procedure 3. Refer to the DOS Manual for detailed 
operation. 

If the following message appears on the display, the system program has been 
transferred to the HDD. 

System Transferred 

If an error message appears on the display, perform Check 4. 

Check 4 

2.5” HDD(s) and the connector(s) of system board may be defective (Refer to the 
steps described in Chapter 4, 

Replacement Procedures

 for disassembling.). Insert 

HDD(s) to the connector(s) firmly. If it is (or they are) firmly connected, go to 
Procedure 3. 

Содержание Portege Z830












































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Portege Z830

EUROCOM Notebook V12.3.10 User Manual preview
Notebook V12.3.10
Бренд: EUROCOM Страницы: 296
Acer Aspire 7735ZG Series Quick Manual preview
Aspire 7735ZG Series
Бренд: Acer Страницы: 13
Acer Aspire 7535 Series Service Manual preview
Aspire 7535 Series
Бренд: Acer Страницы: 220
Acer Aspire 7551G Quick Manual preview
Aspire 7551G
Бренд: Acer Страницы: 9
Siemens FUJITSU AMILO Li Series Getting Started preview
FUJITSU AMILO Li Series
Бренд: Siemens Страницы: 24
Siemens IC 35 User Manual preview
IC 35
Бренд: Siemens Страницы: 30
Siemens Mobile 750 Operating Manual preview
Mobile 750
Бренд: Siemens Страницы: 101
Siemens SIMATIC PG 720 P Manual preview
SIMATIC PG 720 P
Бренд: Siemens Страницы: 124
Siemens SIMATIC Field PG P4 Manual preview
SIMATIC Field PG P4
Бренд: Siemens Страницы: 144
TONGFANG 9560NG User Manual preview
9560NG
Бренд: TONGFANG Страницы: 44
TONGFANG 9560 User Manual preview
9560
Бренд: TONGFANG Страницы: 44
Toshiba Satellite P50-A Series Quick Start Manual preview
Satellite P50-A Series
Бренд: Toshiba Страницы: 8
Toshiba Satellite P305-S8814 Product Specifications preview
Satellite P305-S8814
Бренд: Toshiba Страницы: 3
Toshiba Satellite P305 Specifications preview
Satellite P305
Бренд: Toshiba Страницы: 4
Toshiba Satellite P35-S605 Specification Sheet preview
Satellite P35-S605
Бренд: Toshiba Страницы: 12
Toshiba Satellite P205D-S8812 Specifications preview
Satellite P205D-S8812
Бренд: Toshiba Страницы: 4
Toshiba Satellite P205D-S8804 Specifications preview
Satellite P205D-S8804
Бренд: Toshiba Страницы: 3
Toshiba Satellite P205D-S7802 Specifications preview
Satellite P205D-S7802
Бренд: Toshiba Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды