Toshiba P500DL Скачать руководство пользователя страница 3

Страница: 3 / 44

CONTENTS

SAFETY PRECAUTIONS FOR USER

････････････････････････

PRECAUTIONS FOR USE AND MAINTENANCE

･････････････

GENERAL DESCRIPTIONS

･････････････････････････････････

1. FEATURES

･･･････････････････････････････････････････

2. DIMENSIONS

･････････････････････････････････････････

3. PART NAMES AND FUNCTIONS

･･･････････････････････

3-1. I/O PANEL

････････････････････････････････････････

3-2. POWER PANEL

･･･････････････････････････････････

4. POWER SWITCH AND POWER INDICATOR

････････････

5. SPECIFICATIONS

･････････････････････････････････････

6. ACCEPTABLE SIGNAL TYPE

･･････････････････････････

7. ACCEPTABLE RGB INPUT SIGNAL TIMING

････････････

8. CONNECTION AT A MULTI-PROJECTION SYSTEM

･････

DISASSEMBLY

････････････････････････････････････････････

1. HOW TO REPLACE THE LAMP

････････････････････････

2. LOCATION OF KEY COMPONENTS AND FUNCTION MODULE

･･････

3. EXPLODED VIEW OF THE PROJECTION BLOCK

･･･････

5-1. Removing the DLP engine

･･････････････････････････

5-2. Installing the DLP engine

･･････････････････････････

4. EXPLODED VIEW OF THE SCREEN BLOCK AND CABINET

････････

5. WIRING

･･････････････････････････････････････････････

ADJUSTMENT

･････････････････････････････････････････････

1. ADJUSTING THE DLP ENGINE

････････････････････････

2. ADJUSTING THE ENGINE MOUNT

････････････････････

3. ELECTRONICS ADJUSTMENT OR SETTING

･･･････････

3-1. Input Signal selection

･･････････････････････････････

3-2. Adjust Mode

･･････････････････････････････････････

3-3. Saving adjustments

････････････････････････････････

3-4. Adjustment parameters

････････････････････････････

3-5. Internal Test Pattern

･･････････････････････････････

3-6. White Balance adjustment

･･････････････････････････

3-7. Gain and Off-Set

･･････････････････････････････････

3-8. Clock frequency adjustment and phase adjustment

････

3-9. Image position adjustment

･･････････････････････････

3-10. Screen Mode Selection

････････････････････････････

3-11. On-Screen-Display, OSD

･･･････････････････････････

3-12. Video Enhancer

･･････････････････････････････････

3-13. Interpolation Filter

･･･････････････････････････････

3-14. Image direction

･･･････････････････････････････････

3-15. Status Indication

･････････････････････････････････

3-16. Power ON delay

･･････････････････････････････････

4. Multiple Screen Wall system (example)

･･･････････････････

5. ID Assignment (example)

･･･････････････････････････････

5-1. Clearing I.D.

･･････････････････････････････････････

5-2. Setting I.D.

･･･････････････････････････････････････

5-3. Selecting I.D.

･･････････････････････････････････････

6. Magnification

･･････････････････････････････････････････

Electric Circuit Explanation

･････････････････････････

1. RGB/Control PCB

･････････････････････････････

2. DMD Driver PCB

･･････････････････････････････

3. Power Supply PCB

･････････････････････････････

4. Lamp Ballast PCB

･････････････････････････････

5. RS232C Control PCB

･･････････････････････････

6. Video PCB

････････････････････････････････････

APPENDIX

1. P500DL control board LED status

･･･････････････

2. Control via RS-232C -Command Protocol List

･････

3. DMD Driver board debug

･･･････････････････････

4. PARTS LIST

･･････････････････････････････････

SERVICING DIAGRAM

1. DMD Driver Board Block Diagram

･･････････････

2. Signal Process Section Block Diagram

･･･････････

3. Wiring Diagram

･･･････････････････････････････

4. ENTIRE BLOCK DIAGRAM

････････････････････

5. DMD Board Microcontroller

････････････････････

6. DMD Display Controller

････････････････････････

7. DMD Data Formatter

･･････････････････････････

8. DMD Memory

･････････････････････････････････

9. DMD Switching Voltage

････････････････････････

10. DMD Positive Bias

･････････････････････････････

11. DMD Reset ASIC Driver

････････････････････････

12. DMD Imager

･･････････････････････････････････

13. Motor Rotation Sensor

･･････････････････････････

14. Video Input Buffer

･････････････････････････････

15. RS-232C Board

････････････････････････････････

16. PFC & Main Power Supply

･･････････････････････

17. Sub Power Supply

･･････････････････････････････

18. Video Decoder

･････････････････････････････････

19. Voltage Regulator and Fan Control

･･･････････････

20. 96-pin Connector & D/A Converter

･･･････････････

21. Magnification Scaler

･･･････････････････････････

22. MAG/Freq Conv Control MPU

･･･････････････････

23. Freq Conv Scaler

･･･････････････････････････････

24. Freq Conv Scaler

･･･････････････････････････････

25. Analog SW & A/D Converter

･････････････････････

26. DVI Input Buffer

･･･････････････････････････････

27. DVI Output Buffer

･････････････････････････････

Содержание P500DL













































Результаты поиска

Содержание P500DL

Отзывы:

Бренды по названию

Популярные бренды

Toshiba P500DL, Руководство по обслуживанию

Результаты поиска

Содержание P500DL

Отзывы:

Бренды по названию

Популярные бренды