Toshiba P500DL Скачать руководство пользователя страница 13

Страница: 13 / 44

SPECIFICATIONS

Model name

P500DL

Type

50-inch rear projection unit

Acceptable signals

Refer to page 13 and page 14.

Image device

1 chip XGA Digital Mirror Device

(R)

Light source

120W UHP lamp

Resolution

1024 x 768 dot (Include part hidden with screen frame)

Brightness 500cd/m

(Typ.)

Screen

Fresnel sheet (internal), Lenticular sheet (external)

Screen frame

0.5mm average

Viewing Angle

Horizontal: Min. 150 degrees, Vertical: Min. 60 degrees

Color temperature

Selection of three user defines

Operating temperature

5-35

℃

(41-95

Operating humidity

30-70 % (Relative humidity non-condensing)

Power requirement

AC100-240V, 50/60Hz, 200W (200VA)

Dimensions

1016 (W) x 1050 (H) x 550 (D) mm (40.0 x 41.3 x 21.7 inches)

protrusions not included

Weight 52kg
Accessories

Owner’s Manual, DVI link cable, RS232C link cable, Assembly parts

Video Input

Terminal Not available (Optional Video Input Card : BNC IN/OUT)

Level

(Optional Video Input Card : 1.0Vp-p composite video, PAL/NTSC)

RGB Input

Terminal RGB-1 input / RGB-2 input: HD D-sub 15pin (female) connector x 2

Level

R/G/B signal: 0.7Vp-p (75-ohm termination)

H.SYNC / V.SYNC / C.SYNC signals: TTL

External control

System: RS-232C, Terminal: D-sub 9pin (female) connector x 1

Speed: 1200, 2400, 4800, 9600 baud

Communication Link

System: RS-232C, Terminal: D-sub 9pin connector x 2 for IN and OUT

Digital Signal Link

System: TMDS, Terminal: DVI-D 24pin connector x 2 for IN and OUT

Remote Control Terminal 3.5mm terminal for optional Remote Controller

The Digital Signal Link is used for signal transmission between projection units and this does not
support external input signal.
The specifications and design of this product are subject to change without notice.

○

Содержание P500DL













































Результаты поиска

Содержание P500DL

Отзывы:

Бренды по названию

Популярные бренды

Toshiba P500DL, Руководство по обслуживанию

Результаты поиска

Содержание P500DL

Отзывы:

Бренды по названию

Популярные бренды