ELECTRICAL ADJUSTMENTS
D3-3
2-12: CENTER PARABOLA
1.
2.
3.
4.
Receive the crosshatch signal from the Pattern Generator.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 1-1 and press
the channel button (21) on the remote control to select
“C.PARA”.
Check if the step No. C.PARA is "08".
Press the VOL. UP/DOWN button on the remote control until
the center of the right and left vertical lines are straight.
2-16: TOP CORNER
1.
2.
3.
4.
Receive the crosshatch signal from the Pattern Generator.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (17) on the remote control to
select “COR. TOP”.
Press the VOL. UP/DOWN button on the remote control
until the upper section of the both ends vertical lines are
straight.
2-13: PARABOLA
1.
2.
3.
4.
Receive the crosshatch signal from the Pattern Generator.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (15) on the remote control to
select “EW PARA”.
Press the VOL. UP/DOWN button on the remote control
until the right and left vertical lines are straight.
2-14: CENTER SAW
1.
2.
3.
4.
5.
Receive the crosshatch signal from the Pattern Generator.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (22) on the remote control to
select “C.SAW”.
Check if the step No. C.SAW is "08".
Press the VOL. UP/DOWN button on the remote control
until the difference of the upper section(A) and the bottom
section of the both ends vertical lines becomes minimum.
(Refer to Fig. 2-2)
2-15: CORNER
1.
2.
3.
4.
5.
Receive the crosshatch signal from the Pattern Generator.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (20) on the remote control to
select “CORNER”.
Check if the step No. CORNER is "25".
Press the VOL. UP/DOWN button on the remote control
until the both ends vertical lines are straight.
2-18: OSD HORIZONTAL
Activate the adjustment mode display of Fig. 1-1.
Press the VOL. UP/DOWN button on the remote control
until the difference of A and B becomes minimum. (Refer
to Fig. 2-3)
1.
2.
TV
2-17: BOTTOM CORNER
1.
2.
3.
4.
Receive the crosshatch signal from the Pattern Generator.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (18) on the remote control to
select “COR. BTM”.
Press the VOL. UP/DOWN button on the remote control
until the bottom section of the both ends vertical lines are
straight.
Fig. 2-2
2-19: BRIGHT CENTER
1.
2.
3.
4.
5.
6.
7.
8.
9.
Receive the monoscope pattern. (RF Input)
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (33) on the remote control to
select "BRI CENT".
Press the VOL. UP/DOWN button on the remote control
until the white 15% is starting to be visible
Receive the monoscope pattern. (Audio Video Input)
Press the INPUT SELECT button on the remote control
to set to the AV mode. Then perform the above
adjustments 2~4.
Press the DVD button on the remote control to set to the
DVD mode.
Activate the adjustment mode display of Fig. 1-1 and
press the channel button (33) on the remote control to
select "BRI CENT".
Press the VOL. UP/DOWN button on the remote control
to set the same step numbers as the AV mode.
B
A
00 OSD 07
Fig. 2-3
A
B
a
b
