– 16 –
2
Each time [
] [
] setting button is pushed,
indoor unit numbers in the group control
change cyclically. Select the indoor unit to
change settings for.
• The fan of the selected indoor unit runs . The
indoor unit can be confirmed for which to
change settings.
3
Push OFF timer button to confirm the
selected indoor unit.
4
Push the menu button to make Code No.
[
] flash. Change Code No. [
] with [
]
[
] setting button.
5
Push the menu button to make Set data
[
] flash. Change Set data [
]
with [
] [
] setting button.
6
Push OFF timer button to complete the
setup.
• To change other settings of the selected indoor
unit, repeat from Procedure
4
.
7
When all the settings have been completed,
push ON/OFF button to finish the settings.
(Return to the normal mode)
"
" flashes and then the display content
disappears and the air conditioner enters the
normal stop mode. (The remote controller is
unavailable while "
" is flashing.)
• To change settings of another indoor unit,
repeat from Procedure
1
.
To secure better effect of
heating
When it is difficult to obtain satisfactory heating due to
installation place of the indoor unit or structure of the
room, the detection temperature of heating can be
raised. Also use a circulator or other machinery to
circulate heat air near the ceiling.
Follow to the basic operation procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[06]
for the Code No. in Procedure
4
.
• For the set data in Procedure
5
, select the set data
of shift value of detection temperature to be set up
from the following table.
Filter sign setting
According to the installation condition, the filter sign
term (Notification of filter cleaning) can be changed.
Follow to the basic operation procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[01]
for the Code No. in Procedure
4
.
• Select the set data of filter sign term from the
following table for the set data in Procedure
5
.
• The filter sign may be unavailable depending on the
remote controllers.
Set data
Code No.
Set data
Detection temperature shift value
0000
No shift
(Factory default)
0001
+1°C
0002
+2°C
0003
+3°C
0004
+4°C
0005
+5°C
0006
+6°C
Set data
Filter sign term
0000
None
0001
150 H
(Factory default)
0002
2500 H
0003
5000 H
0004
10000 H
Remote controller sensor
The temperature sensor of the indoor unit senses room
temperature usually. Set the remote controller sensor
to sense the temperature around the remote controller.
Select items following the basic operation procedure
(
1
→
2
→
3
→
4
→
5
→
6
→
7
).
• Specify
[32]
for the Code No. in Procedure
4
.
• Select the following data for the set data in
Procedure
5
.
When
flashes, the remote controller sensor is
defective.
Select the set data [0000] (not in use) or replace the
remote controller.
Group control
In a group control, a remote controller can control up to
maximum 8 or 16 units. (Depending on the outdoor
unit.)
• The wired remote controller only can control a group
control. The wireless remote controller is unavailable
for this control.
• For wiring procedure and wires of the individual line
(Identical refrigerant line) system, refer to
“7 Electrical connection” in this Manual.
• Wiring between indoor units in a group is performed
in the following procedure.
• Connect the indoor units by connecting the remote
controller wires from the remote controller terminal
blocks (A, B) of the indoor unit connected with a
remote controller to the remote controller terminal
blocks (A, B) of the other indoor unit. (Non-polarity)
• For address setup, refer to the Installation Manual
attached to the outdoor unit.
Set data
0000
0001
Remote controller
sensor
Not in use
(Factory default)
In use
31-EN
32-EN
Содержание MML-UP0071BH-E
Страница 28: ...EB99841301 ...
