Toshiba GD-1190 Скачать руководство пользователя страница 12

Страница: 12 / 70

GD-1190 INSTALLATION PROCEDURE 2 - 2

4) Align the top frame portion of the FAX modem PWB with the screw

hole at the back of the speaker unit.

5) Place the holes of the bottom portion of the FAX modem PWB onto

the loosely tightened screws.

Slide the PWB to left to secure as shown below.

6) Secure the ground terminal and the FAX modem PWB onto the

copier using the screw removed earlier in Step 2).

7) Secure the FAX modem PWB onto the copier using a supplied

screw.

8) Tighten t

loosely tightened screws completely.

9) Secure FAX modem PWB aluminum sheet onto the copier using a

supplied screws.

10) Unscrew the screw securing the ground terminal of the motor

plate, and secure it again together with the ground terminal of the
FAX PWB as shown.

(5) Connect the flat cable A, the flat cable B, and the

speaker connector

Connect the copier and the modem PWB with the flat cable B.

Connect the copier and the modem PWB with the flat cable A.

NOTE: The blue side of the cables must be outer side.

Connect the speaker connector to the modem PWB.

(6) Work the rear cabinet, and attach the gasket.

1) Cut and remove the cut-out portion from the rear cabinet using a

tool such as nippers. (Be careful with the tool’s direction so that the
cut surface is flat.)

2) Attach the gasket as shown.

(7) Reattach the rear cabinet.

1) Reattach the rear cabinet and secure it using three screws.

2) Reattach the rear cabinet shielding plate and secure it using one

screw removed earlier.

Reattach the ADF

/ RADF

detached in Step (1).

(8) Peel off the dummy key sheet.

Open the ADF

/ RADF

cover.

Peel the edge of the dummy key sheet using a tool such as a retract-
able knife, and then peel off the entire key sheet.

(9) Remove the dummy keyboard.

Unscrew the screw, and remove the dummy keyboard with a tool like a
pillar as shown below. (Save the screw.)

ARFX9̲A1E.book 2 ページ２００４年１２月３日金曜日午後４時２２分

Содержание GD-1190







































































Результаты поиска

Содержание GD-1190

Отзывы:

Похожие инструкции для GD-1190

Бренды по названию

Популярные бренды

Toshiba GD-1190, Руководство по обслуживанию

Результаты поиска

Содержание GD-1190

Отзывы:

Похожие инструкции для GD-1190

Бренды по названию

Популярные бренды