Toshiba GD-1190 Скачать руководство пользователя страница 11

Страница: 11 / 70

GD-1190 INSTALLATION PROCEDURE 2 - 1

[2] INSTALLATION PROCEDURE

<Before installation>

For improvement of workability, some description in this manual as
well as components and accessories may change without prior notice.
In this case, refer to the service manual.

Turn off the main switch of the copier and then remove the power plug
of the copier from the outlet.

1. Parts included

2. Installation procedure

(1) Detach the ADF

RADF

Detach the ADF

RADF

from the copier and softly place it on top of the

original

table as shown below.

(2) Remove the rear cabinet.

1) Unscrew the screw and remove the rear cabinet shielding plate.

(Save the screw.)

2) Unscrew three screws and remove the rear cabinet. (Save the

screws.)

(3) Attach the speaker unit.

Attach the speaker unit using a supplied screw as shown below.

(4) Attach the FAX modem PWB.

1) Attach sponge A and sponge B on the back of FAX PWB.

2) Unscrew the screw holding the ground terminal of the copier.

(Save the screw.)

3) Insert two supplied screws and tighten them loosely as shown

below.

The unpacking and set-up procedure shall be done by a qualified
service technician.

02_INSTALLATION.fm 1

ページ

２００５年１月６日　木曜日　午後２時１５分

Содержание GD-1190







































































Результаты поиска

Содержание GD-1190

Отзывы:

Похожие инструкции для GD-1190

Бренды по названию

Популярные бренды

Toshiba GD-1190, Руководство по обслуживанию

Результаты поиска

Содержание GD-1190

Отзывы:

Похожие инструкции для GD-1190

Бренды по названию

Популярные бренды