Toshiba B-SA4T Скачать руководство пользователя | Manualshive

Страница: 33 / 45

background image

2. SUPPLY SPECIFICATIONS

EO10-33016A

(Revision Date: Feb. 14, 2008)

2.4 Specification of RFID Tag

2- 12

2.4.6 Printing on Bump (Chip/Antenna) Area

Embedding RFID tags in labels creates bumps in a chip/antenna area in the labels, causing incomplete
printing.

Especially, in the areas 5 mm from and left and right sides of the RFID-tag embedded area shown in the
figure below, uneven printing or incomplete printing can occur easily.

NOTE: The degree of poor printing quality differs depending on height of a chip/antenna used.

Media
feed
direction

RFID tag
embedded
area

Print quality on the
sides of RFID tag
is not guaranteed.

Print quality on
bumps is not
guaranteed.

Print quality on
bumps is not
guaranteed.

Print quality on
the IC chip is not
guaranteed.

5mm

2.4.7 Ambient Temperature

Low temperature deteriorates wireless performance, under which conditions writing data on an RFID tag
may fail.

2.4.8 Strip Issue

Stripping performance in strip issue mode depends on the type of glue, tag, and backing paper. For some

RFID supplies used, an issue may not be performed properly in strip issue mode.

5mm

«
...
31
32
33
34
35
...
»

Содержание B-SA4T














































Отзывы:

Нет отзывов

Похожие инструкции для B-SA4T

M-Class Mark II

Бренд: Datamax Страницы: 6

Бренд: Pocketbook Страницы: 105

Sentinel-Prox DC-1023

Бренд: AWID Страницы: 12

Бренд: bioscrypt Страницы: 72

Бренд: Symcode Страницы: 56

Бренд: Honeywell Страницы: 44

Бренд: Hama Страницы: 42

Бренд: Siemens Страницы: 34

Бренд: Scannel Страницы: 35

Бренд: Scandex Страницы: 15

Бренд: XTIOT Страницы: 4

Бренд: PlusQuip Страницы: 57

Бренд: Godex Страницы: 45

Бренд: Godex Страницы: 56

Бренд: Rosslare Страницы: 66

DL Cordless Card

Бренд: Datalogic Страницы: 55

Бренд: Datalogic Страницы: 119

Бренд: Datalogic Страницы: 203

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды