background image

E-5 

3.  Turning the Printer  
 ON/OFF 

 

 

3.1 

Turning ON the 
Printer

 

 
 
 
 
 
 

When the printer is connected to a host computer it is good practice to 
turn the printer ON before turning on the host computer and to turn 
OFF the host computer before turning off the printer. 

 

NOTE: 

Before turning the printer ON, it is necessary to setup the printer 

correctly. 

For instructions on how to setup the printer, refer to 

2.2 Procedure 

before Operation

 of the Owner’s Manual. 

 

 

1.

 

To turn ON the printer power, press the power switch as shown in 
the diagram below.  Note that ( | ) is the power ON side of the 
switch. 

 

 

 

2.

 

Check that LED 1 stays illuminated in green. 

CAUTION! 

Use the power switch to 
turn the printer on/off.  
Plugging or unplugging the 
power cord to turn the 
printer on/off may cause 
fire, an electric shock, or 
damage to the printer. 

 

Power Switch 

NOTE: 

If LED 1 is illuminated in colors 
other than green or unlit, refer to 

Section 4, 
TROUBLESHOOTING 

of the 

Owner’s Manual. 

 

E-6 

3.2 

Turning OFF the  
Printer 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 

 

 

 

 

 

 

 

 

 

 

 

1.

 

Before turning off the printer power switch, verify the following:

  LED 1 is illuminated in green, not flashing. 
  LED 2 is extinguished. 
 

2. 

To turn OFF the printer power, press the power switch as shown in 
the diagram below.  Note that ( 

 ) is the power OFF side of the 

switch. 

 

 

 

 

 

 

CAUTION! 

1.  Do not turn off the printer 

power while the media is 
being printed as this may 
cause a paper jam or 
damage to the printer. 

2.  Do not turn off the printer 

power while LED 1 is 
flashing as this may cause 
damage to the data being 
downloaded. 

Power Switch 

Содержание B-FV4D SERIES








Отзывы: