Toshiba 35PAVSG-ND, Руководство по установке

Страница: 10 / 80

How to remove the drain cap
Clip the drain cap by needle-nose
pliers and pull out.
How to remove the drain hose
‡ The drain hose can be removed by removing the
screw securing the drain hose and then pulling out
the drain hose.
‡ When removing the drain hose, be careful of any
sharp edges of steel plate. The edges can injuries.
‡ To install the drain hose, insert the drain hose
fi rmly until the connection part contacts with heat
insulator, and then secure it with original screw.
How to fi x the drain cap
1) Insert hexagon wrench (4 mm)
in a center head.
2) Firmly insert the drain cap.
Firmly insert the drain hose and drain cap; otherwise, water may leak.
CAUTION
Drain hose
Left-hand connection with piping
‡ Bend the connecting pipe so that it is laid within 43 mm above the wall
surface. If the connecting pipe is laid exceeding 43 mm above the wall
surface, the indoor unit may unstably be set on the wall.
When bending the connecting pipe, make sure to use a spring bender so
as not to crush the pipe.
Bend the connecting pipe within a radius of 30 mm.
To connect the pipe after installation of the unit (fi gure)
NOTE
If the pipe is bent incorrectly, the indoor unit may unstably be set on the wall.
After passing the connecting pipe through the pipe hole, connect the
connecting pipes to the auxiliary pipes and wrap the facing tape around
them.
In case of right or left piping
‡ After scribing slits of the back body
with a knife or a making-off pin, cut
them with a pair of nippers or an
equivalent tool.
In case of bottom right or bottom left piping
‡ After scribing slits of the back body
with a knife or a making-off pin, cut
them with a pair of nippers or an
equivalent tool.
Slit
Slit
CAUTION
‡ Bind the auxiliary pipes (two) and connecting cable with facing tape
tightly. In case of leftward piping and rear-leftward piping, bind the
auxiliary pipes (two) only with facing tape.
Indoor unit
Connecting cable
Auxiliary pipes
Installation plate
‡ Carefully arrange pipes so that any pipe does not stick out of the rear
plate of the indoor unit.
‡ Carefully connect the auxiliary pipes and connecting pipes to one
another and cut off the insulating tape wound on the connecting pipe to
avoid double-taping at the joint; moreover, seal the joint with the vinyl
tape, etc.
‡ Since dewing results in a machine trouble, make sure to insulate both
connecting pipes. (Use polyethylene foam as insulating material.)
‡ When bending a pipe, carefully do it, not to crush it.
1
2
1
Hook here.
Installation plate
Hook
Press
(unhook)
Push
Push
Indoor Unit Fixing
‡ For detaching the indoor unit from
the installation plate, pull the indoor
unit toward you while pushing its
bottom up at the specifi ed parts.
1. Pass the pipe through the hole in the wall and hook the indoor unit on the
installation plate at the upper hook.
2. Swing the indoor unit to right and left to confi rm that it is fi rmly hooked up on
the installation plate.
3. While pressing the indoor unit onto the wall, hook it at the lower part on the
installation plate. Pull the indoor unit toward you to confi rm that it is fi rmly
hooked up on the installation plate.
Do not apply lubricating oil
(refrigerant machine oil)
when inserting the drain
cap. Application causes
deterioration and drain
leakage of the plug.
Insert a hexagon wrench
(4 mm).
No gap
WARNING
‡ Do not perform flare connection inside a building or dwelling or room,
when joining the heat exchanger of indoor unit with interconnection
piping. Refrigerant connection inside a building or dwelling or room
must be made by brazing or welding. Joint connection of indoor unit by
flaring method can only be made at outdoor or at outside of building or
dwelling or room. Flare connection may cause gas leak and flammable
atmosphere.
43
mm
80
°
260 mm
210 mm
Use the handle of screwdriver, etc.
Outward form of indoor unit
R 30 mm (Use polisin (polyethylene)
core or the like for bending pipe.)
Gas side
Liquid side
8
1118350136_(01_EN).indd 8 1118350136_(01_EN).indd 8 7/20/17 11:57 AM 7/20/17 11:57 AM