Toshiba 32A32 Скачать руководство пользователя

Страница: 13 / 33

– 13 –

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

ITEM

ADJUSTMENT PROCEDURE

HORIZONTAL POSITION
(HPOS)
VERTICAL POSITION
(VPOS)

1. Call up the adjustment mode display, then select the item

HPOS

VPOS

2. Press the TV/VIDEO button on Remote until the

white cross-bar or black cross-bar pattern appears
on the screen.

3. Adjust the HORIZONTAL and VERTICAL position

alternately by pressing the VOLUME

button

for proper picture position.

4. Check the picture with off-air signal.

HEIGHT
(HIT)

1. Call up the adjustment mode display, then select the item

HIT

2. Press the VOLUME

button to get the picture so the top of raster begins

to lack.

3. Press the VOLUME

button to advance the data by 8 steps.

Note : Check the vertical picture position is correct.

WHITE BALANCE
(RCUT)
(GCUT)
(BCUT)
(GDRV)
(BDRV)

1. Adjust the CONTRAST control to the center, and BRIGHTNESS control to the

maximum.

2. Call up the adjustment mode display, and press the TV/VIDEO button on

Remote until the white and black pattern appears on the screen.

3. Adjust the following item with the CHANNEL

and VOLUME

buttons.

4. Press the TV/VIDEO button on TV to display a single horizontal line on the

screen.

5. Turn the SCREEN control (FBT) fully counterclockwise and gradually rotate

clockwise until the first horizontal line appears slightly on the screen.

6. Press the TV/VIDEO button to display the normal picture.
7. Adjust the remaining two “?CUT” items (CHANNEL

→

TV/VIDEO

→

VOLUME

in order) to obtain the slightly lighted horizontal line in the same

levels of three (red, green, blue) colors. The line should be white if the adjust-
ments are proper.

Bright area
Adjust "GDRV" or "BDRV" to be white.

Dark area
Fine adjust "RCUT", "GCUT" or "BCUT" to be black.

RCUT

Data : 40H

GCUT

Data : 40H

BCUT

Data : 40H

GDRV

Data : 80H

BDRV

Data : 80H

E-W PARABOLA
(DPC)

1. Call up the adjustment mode display, then select the item

DPC

2. Press the TV/VIDEO button on Remote until the cross-hatch pattern appears on

the screen.

3. Press the VOLUME

button to make vertical lines straight as shown

below.

Содержание 32A32


































Результаты поиска

Содержание 32A32

Отзывы:

Похожие инструкции для 32A32

Бренды по названию

Популярные бренды

Toshiba 32A32, Руководство по обслуживанию

Результаты поиска

Содержание 32A32

Отзывы:

Похожие инструкции для 32A32

Бренды по названию

Популярные бренды