manualshive.com logo in svg

Torrent 30" SHARK, Руководство пользователя

Поделиться
Скачать
Torrent 30

 

 

 

30" SHARK 

Owner’s Manual

 

4

 

WARNING: 

Because of the nature of the hydraulic motor protective valving supplied on the 

mulching unit, the cutting drum will continue to rotate after the unit is shut down until all 
inertial energy is expended from the cutting drum. Always allow the unit at least two 
minutes 

to “run

-

down” after the carrier has been shut down before approaching the unit for 

any reason. 

WARNING: 

This machine must be installed according to the product technical specifications 

contained herein by qualified technical personnel only. RWI Ltd. accepts no responsibility for 
damage or injury resulting from inadequate or improper installation of its products. 

WARNING: 

When servicing cutters, the cutting drum must be mechanically prevented from 

turning (that is, wedged or blocked) to minimize the risk of injury to the maintainer. 

WARNING: 

The 30

” SHARK

 is manufactured from metal components and, as such, is a highly 

efficient electrical conductor. Extreme caution must be used when working around electric 
power transmission lines whether above or belowground! 

WARNING: 

This machine must be installed and used in observance of all laws, rules and 

regulations as laid out by local regulatory bodies in the country/region in which it is being 
used. 

 

 

Содержание 30" SHARK



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды