Torque Fitness TQ5-001 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 46

background image

(THIS CHECKLIST MUST BE FILLED OUT IN ITS ENTIRETY AND LEFT WITH THE OWNER)

Product Serial Number _______________________________ Date Assembled _____________

Authorized Dealer _________________________ Assembler(s) __________________________

POST ASSEMBLY ADJUSTMENTS / CHECKS:

_______

Ensure ALL connections are tightened according to the instructions.

_______

Cable Tension Adjustment (See Step 29): ensure that the head plate rests on the first weight plate yet there is not a lot of slop in the cable
system. If the head plate is not resting on the first plate or if there is too much cable slop in the system you can adjust cable tension in the
following places (in sequential order):

1. Where the threaded end of the WEIGHT STACK CABLE (64) attaches to the HEAD PLATE (61) (See Step 17).

2. Where the FLOATING PULLEY CABLES (66) thread into the 4-1/2” FLOATING PULLEY (35). (See Step 22)

_______

Ensure all adjustments are smooth and easy and that pull pin easily engages and disengages in all of the adjustment holes.

_______

Ensure cables are routed according to instructions and are not rubbing on cable retaining clips or retaining bolts. If when using, it feels like there is
cable drag, it is most likely that a cable retaining clip is out of position and the cable is rubbing on it or the cable has been routed incorrectly and is
riding on top of a cable retaining bolt. Also, loose pulley connections can make travel feel rough, check that all pulley connections are tight. Check
all areas where this applies. The product should work very smoothly.

______

Ensure the Torque Fork™ weight adjuster easily fits in-between each of the weight plates.

Assembly Checklist

Page 41

Hybrid

TM

Strength Technology Gym System

«
...
39
40
41
42
43
...
»

Содержание TQ5-001















































Отзывы:

Нет отзывов

Похожие инструкции для TQ5-001

Бренд: SportsArt Fitness Страницы: 32

Бренд: Impulse Страницы: 11

Flat Bench Sa 10-4

Бренд: Weider Страницы: 8

Бренд: Weider Страницы: 23

Бренд: Weider Страницы: 28

Бренд: Hoist Fitness Страницы: 84

Бренд: LifeGear Страницы: 45

Бренд: Inspire Страницы: 23

Бренд: Inspire Страницы: 30

Бренд: ParaBody Страницы: 3

Бренд: NordicTrack Страницы: 15

Бренд: NordicTrack Страницы: 20

Бренд: Weider Страницы: 1

Бренд: Weider Страницы: 8

Body Works Pro 2.0

Бренд: Weider Страницы: 12

Бренд: Tumbl Trak Страницы: 9

Cardio Kids 680e

Бренд: KIDSFIT Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды