Toro Z450 Z Master Скачать руководство пользователя страница 45

Страница: 45 / 60

Figure 59

1. Double nuts

3. Locknut

2. Pump rod

4. Ball joint

Electrical system will not perform proper
safety shut off with jumper wire installed.

•

Remove jumper wire from wire
harness connector and plug
connector into seat switch when
adjustment is completed.

•

Never operate this unit with jumper
installed and seat switch bypassed.

7. After both pump neutrals are set, shut off the

machine.

8. Remove the jumper wire from the wire harness

connector and plug the connector into the seat
switch.

9. Install the seat rod and lower the seat into

position.

10. Remove the jack stands.

Mower Deck

Maintenance

Leveling the Mower at Three

Positions

Important:

There are only three measuring

positions needed to level the mower.

Setting Up the Machine

1. Position mower on a ﬂat surface.
2. Disengage the PTO, move the motion control

levers to the neutral locked position and set
the parking brake.

3. Stop the engine, remove the key, and wait for

all moving parts to stop before leaving the
operating position.

4. Check tire pressure of all four tires. If needed,

adjust to 13 psi (90 kPa)

5. Lower the mower to the 3 inch (76 mm)

height-of-cut position.

6. Inspect the four chains. The chains need to

have tension.

Note:

Adjust the rear chains to the top of the

slot, where they are attached to the mower.

•

If one rear chain is loose, lower (loosen) the
front support arm on the same side. Refer to
Adjusting the Front-to-Rear Mower Pitch.

•

If one front chain is loose, raise (tighten) the
front support arm for that chain. Refer to
Adjusting the Front-to-Rear Mower Pitch.

Leveling the Mower Side-to-Side

1. Position the right blade front-to-rear

(Figure 60).

2. Measure the right blade at the

location, from

a level surface to the cutting edge of the blade
tip (Figure 60).

3. Record this measurement. This measurement

needs to be 3-1/8 to 3-1/4 inches.

4. Position the left blade front-to-rear (Figure 60).
5. Measure the left blade at the

location

(Figure 60), from a level surface to the cutting
edge of the blade tip .

6. Record this measurement. This measurement

needs to be 3-1/8 to 3-1/4 inches (79 to
83mm).

Содержание Z450 Z Master





























































Результаты поиска

Содержание Z450 Z Master

Отзывы:

Бренды по названию

Популярные бренды

Toro Z450 Z Master, Руководство оператора

Результаты поиска

Содержание Z450 Z Master

Отзывы:

Бренды по названию

Популярные бренды