Toro Z450 Z Master Скачать руководство пользователя страница 38

Страница: 38 / 60

Figure 47

1. Engine air intake

2. Blower housing

Cleaning the Cooling System

Check and clean cooling ﬁns and engine shrouds
every 100 hours or yearly, which ever comes ﬁrst.

1. Disengage the PTO and set the parking brake.

2. Stop the engine, remove the key, and wait for

all moving parts to stop before leaving the
operating position.

3. Remove the blower housing and engine

shrouds (Figure 47).

4. Clean the debris and grass from the engine

parts.

5. Install the blower housing and engine shrouds.

Brake Maintenance

Adjusting the Parking Brake

Check the parking brake for proper adjustment.

1. Disengage the brake lever (lever down).

2. Measure the length of the spring; the

measurement should be 2-3/4 inch (74 mm)
between the washers (Figure 48).

Figure 48

1. Brake lever

5. 3/16 to 1/4 inch (5 to

7 mm)

2. Spring, 2-3/4 inch (74 mm) 6. Jam nut and yoke

3. Adjusting nuts

7. Trunnion

4. Collar on brake rod

3. If an adjustment is necessary, do the following:

A. Loosen the jam nut below the spring and

tighten the nut directly below the yoke
(Figure 48).

B. Turn the nut until you obtain the correct

measurement.

C. Tighten the 2 nuts together and repeat on

the opposite side of the machine.

4. Turn the nuts clockwise to shorten the spring

length; counterclockwise to lengthen the
spring.

5. Engage the parking brake, with the lever up.
6. Measure the distance between the trunnion

roller and the collar on the brake rod. The
measurement should be 3/16 to 1/4 inch (5
to 7 mm) (Figure 48).

7. If an adjustment is necessary, do the following:

A. Loosen the jam nut directly below the yoke.
B. Turn the bottom adjusting nuts until

the correct measurement is obtained
(Figure 48).

C. Tighten the jam nut at the yoke.

Belt Maintenance

Inspecting the Belts

Inspect all belts every 100 hours.

Содержание Z450 Z Master





























































Результаты поиска

Содержание Z450 Z Master

Отзывы:

Бренды по названию

Популярные бренды

Toro Z450 Z Master, Руководство оператора

Результаты поиска

Содержание Z450 Z Master

Отзывы:

Бренды по названию

Популярные бренды